PIC24FJ256DA210 Datasheet, PDF (206/408 Pages) Microchip Technology – 64/100-Pin, 16-Bit Flash Microcontrollers with Graphics Controller and USB On-The-Go (OTG)

PIC24FJ256DA210 FAMILY
REGISTER 14-1: OCxCON1: OUTPUT COMPARE x CONTROL REGISTER 1
U-0
—
bit 15
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
OCSIDL
OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2⁽²⁾
R/W-0
ENFLT1⁽²⁾
bit 8
R/W-0
ENFLT0⁽²⁾
bit 7
R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0
OCFLT2⁽²⁾ OCFLT1⁽²⁾ OCFLT0⁽²⁾ TRIGMODE
R/W-0
OCM2⁽¹⁾
R/W-0
OCM1⁽¹⁾
R/W-0
OCM0⁽¹⁾
bit 0
Legend:
R = Readable bit
-n = Value at POR
HSC = Hardware Settable/Clearable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 15-14
bit 13
bit 12-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
Unimplemented: Read as ‘0’
OCSIDL: Stop Output Compare x in Idle Mode Control bit
1 = Output Compare x halts in CPU Idle mode
0 = Output Compare x continues to operate in CPU Idle mode
OCTSEL<2:0>: Output Compare x Timer Select bits
111 = Peripheral clock (FCY)
110 = Reserved
101 = Reserved
100 = Timer1 clock (only synchronous clock is supported)
011 = Timer5 clock
010 = Timer4 clock
001 = Timer3 clock
000 = Timer2 clock
ENFLT2: Fault Input 2 Enable bit⁽²⁾
1 = Fault 2 (Comparator 1/2/3 out) is enabled⁽³⁾
0 = Fault 2 is disabled
ENFLT1: Fault Input 1 Enable bit⁽²⁾
1 = Fault 1 (OCFB pin) is enabled⁽⁴⁾
0 = Fault 1 is disabled
ENFLT0: Fault Input 0 Enable bit⁽²⁾
1 = Fault 0 (OCFA pin) is enabled⁽⁴⁾
0 = Fault 0 is disabled
OCFLT2: PWM Fault 2 (Comparator 1/2/3) Condition Status bit^(2,3)
1 = PWM Fault 2 has occurred
0 = No PWM Fault 2 has occurred
OCFLT1: PWM Fault 1 (OCFB pin) Condition Status bit^(2,4)
1 = PWM Fault 1 has occurred
0 = No PWM Fault 1 has occurred
OCFLT0: PWM Fault 0 (OCFA pin) Condition Status bit^(2,4)
1 = PWM Fault 0 has occurred
0 = No PWM Fault 0 has occurred
Note 1:
2:
3:
4:
The OCx output must also be configured to an available RPn pin. For more information, see Section 10.4
“Peripheral Pin Select (PPS)”.
The Fault input enable and Fault status bits are valid when OCM<2:0> = 111 or 110.
The Comparator 1 output controls the OC1-OC3 channels; Comparator 2 output controls the OC4-OC6
channels; Comparator 3 output controls the OC7-OC9 channels.
The OCFA/OCFB Fault input must also be configured to an available RPn/RPIn pin. For more information,
see Section 10.4 “Peripheral Pin Select (PPS)”.
DS39969B-page 206
 2010 Microchip Technology Inc.