PIC24FJ256DA210 Datasheet, PDF (225/408 Pages) Microchip Technology – 64/100-Pin, 16-Bit Flash Microcontrollers with Graphics Controller and USB On-The-Go (OTG)

PIC24FJ256DA210 FAMILY
16.2 Setting Baud Rate When
Operating as a Bus Master
To compute the Baud Rate Generator reload value, use
Equation 16-1.
EQUATION 16-1: COMPUTING BAUD RATE
RELOAD VALUE^(1,2)
or:
FSCL =
FCY
I2CxBRG
+
1
+
FCY
10,000,000
( ) I2CxBRG =
FCY
FSCL
–
FCY
10,000,000
–1
Note 1: Based on FCY = FOSC/2; Doze mode and
PLL are disabled.
2: These clock rate values are for guidance
only. The actual clock rate can be affected
by various system level parameters. The
actual clock rate should be measured in
its intended application.
16.3 Slave Address Masking
The I2CxMSK register (Register 16-3) designates
address bit positions as “don’t care” for both 7-Bit and
10-Bit Addressing modes. Setting a particular bit loca-
tion (= 1) in the I2CxMSK register causes the slave
module to respond whether the corresponding address
bit value is a ‘0’ or a ‘1’. For example, when I2CxMSK
is set to ‘00100000’, the slave module will detect both
addresses, ‘0000000’ and ‘0100000’.
To enable address masking, the Intelligent Peripheral
Management Interface (IPMI) must be disabled by
clearing the IPMIEN bit (I2CxCON<11>).
Note:
As a result of changes in the I²C™ proto-
col, the addresses in Table 16-2 are
reserved and will not be Acknowledged in
Slave mode. This includes any address
mask settings that include any of these
addresses.
TABLE 16-1: I2C™ CLOCK RATES(1,2)
Required System FSCL
FCY
I2CxBRG Value
(Decimal)
(Hexadecimal)
Actual FSCL
100 kHz
16 MHz
157
9D
100 kHz
100 kHz
8 MHz
78
4E
100 kHz
100 kHz
4 MHz
39
27
99 kHz
400 kHz
16 MHz
37
25
404 kHz
400 kHz
8 MHz
18
12
404 kHz
400 kHz
4 MHz
9
9
385 kHz
400 kHz
2 MHz
4
4
385 kHz
1 MHz
16 MHz
13
D
1.026 MHz
1 MHz
8 MHz
6
6
1.026 MHz
1 MHz
4 MHz
3
3
0.909 MHz
Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled.
2: These clock rate values are for guidance only. The actual clock rate can be affected by various system
level parameters. The actual clock rate should be measured in its intended application.
TABLE 16-2: I²C™ RESERVED ADDRESSES⁽¹⁾
Slave Address R/W Bit
Description
0000 000
0
General Call Address⁽²⁾
0000 000
1 Start Byte
0000 001
x CBus Address
0000 01x
x Reserved
0000 1xx
1111 0xx
x HS Mode Master Code
x
10-Bit Slave Upper Byte⁽³⁾
1111 1xx
x Reserved
Note 1: The address bits listed here will never cause an address match, independent of address mask settings.
2: The address will be Acknowledged only if GCEN = 1.
3: A match on this address can only occur on the upper byte in 10-Bit Addressing mode.
 2010 Microchip Technology Inc.
DS39969B-page 225