PIC18F67J11-IPT Datasheet, PDF (290/448 Pages) Microchip Technology – 64/80-Pin High-Performance, 1-Mbit Flash Microcontrollers with nanoWatt Technology

PIC18F87J11 FAMILY
TABLE 20-8: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Name
Bit 7
Bit 6
Bit 5 Bit 4 Bit 3
Bit 2
Bit 1
Bit 0
Reset Values
on Page:
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF
57
PIR1
PMPIF
ADIF RC1IF TX1IF SSP1IF CCP1IF TMR2IF TMR1IF
60
PIE1
PMPIE ADIE RC1IE TX1IE SSP1IE CCP1IE TMR2IE TMR1IE
60
IPR1
PMPIP ADIP RC1IP TX1IP SSP1IP CCP1IP TMR2IP TMR1IP
60
PIR3
SSP2IF BCL2IF RC2IF TX2IF TMR4IF CCP5IF CCP4IF CCP3IF
60
PIE3
SSP2IE BCL2IE RC2IE TX2IE TMR4IE CCP5IE CCP4IE CCP3IE
60
IPR3
SSP2IP BCL2IP RC2IP TX2IP TMR4IP CCP5IP CCP4IP CCP3IP
60
RCSTAx
SPEN
RX9 SREN CREN ADDEN FERR OERR RX9D
59
RCREGx EUSARTx Receive Register
59
TXSTAx
CSRC
TX9
TXEN SYNC SENDB BRGH TRMT TX9D
59
BAUDCONx ABDOVF RCIDL RXDTP TXCKP BRG16
—
WUE ABDEN
61
SPBRGHx EUSARTx Baud Rate Generator Register High Byte
61
SPBRGx EUSARTx Baud Rate Generator Register Low Byte
61
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
20.4 EUSART Synchronous
Slave Mode
Synchronous Slave mode is entered by clearing bit,
CSRC (TXSTAx<7>). This mode differs from the
Synchronous Master mode in that the shift clock is sup-
plied externally at the CKx pin (instead of being supplied
internally in Master mode). This allows the device to
transfer or receive data while in any low-power mode.
20.4.1 EUSART SYNCHRONOUS
SLAVE TRANSMISSION
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep mode.
If two words are written to the TXREGx and then the
SLEEP instruction is executed, the following will occur:
a) The first word will immediately transfer to the
TSR register and transmit.
b) The second word will remain in the TXREGx
register.
c) Flag bit, TXxIF, will not be set.
d) When the first word has been shifted out of TSR,
the TXREGx register will transfer the second
word to the TSR and flag bit, TXxIF, will now be
set.
e) If enable bit, TXxIE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
To set up a Synchronous Slave Transmission:
1. Enable the synchronous slave serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
2. Clear bits, CREN and SREN.
3. If interrupts are desired, set enable bit, TXxIE.
4. If 9-bit transmission is desired, set bit, TX9.
5. Enable the transmission by setting enable bit,
TXEN.
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit, TX9D.
7. Start transmission by loading data to the
TXREGx register.
8. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
DS39778D-page 290
© 2009 Microchip Technology Inc.