MC68HC08GZ32 Datasheet, PDF (25/320 Pages) Freescale Semiconductor, Inc – Microcontrollers

Pin Functions
1.5.4 External Interrupt Pin (IRQ)
IRQ is an asynchronous external interrupt pin. This pin contains an internal pullup resistor. See
Chapter 8 External Interrupt (IRQ).
1.5.5 CGM Power Supply Pins (V_DDA and V_SSA)
V_DDA and V_SSA are the power supply pins for the analog portion of the clock generator module (CGM).
Decoupling of these pins should be as per the digital supply. See Chapter 4 Clock Generator Module
(CGM).
1.5.6 External Filter Capacitor Pin (CGMXFC)
CGMXFC is an external filter capacitor connection for the CGM. See Chapter 4 Clock Generator Module
(CGM).
1.5.7 ADC Power Supply/Reference Pins (V_DDAD/V_REFH and V_SSAD/V_REFL)
V_DDAD and V_SSAD are the power supply pins to the analog-to-digital converter (ADC). V_REFH and V_REFL
are the reference voltage pins for the ADC. V_REFH is the high reference supply for the ADC, and by default
the V_DDAD/V_REFH pin should be externally filtered and connected to the same voltage potential as V_DD.
V_REFL is the low reference supply for the ADC, and by default the V_SSAD/V_REFL pin should be connected
to the same voltage potential as V_SS. See Chapter 3 Analog-to-Digital Converter (ADC).
1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15–PTA0/KBD0/AD8)
PTA7–PTA0 are general-purpose, bidirectional I/O port pins. Any or all of the port A pins can be
programmed to serve as keyboard interrupt pins or used as analog-to-digital inputs. PTA7–PTA4 are only
available on the 48-pin LQFP and 64-pin QFP packages. See Chapter 13 Input/Output (I/O) Ports,
Chapter 9 Keyboard Interrupt Module (KBI), and Chapter 3 Analog-to-Digital Converter (ADC).
These port pins also have selectable pullups when configured for input mode. The pullups are disengaged
when configured for output mode. The pullups are selectable on an individual port bit basis.
1.5.9 Port B I/O Pins (PTB7/AD7–PTB0/AD0)
PTB7–PTB0 are general-purpose, bidirectional I/O port pins that can also be used for analog-to-digital
converter (ADC) inputs. PTB7–PTB6 are only available on the 48-pin LQFP and 64-pin QFP packages.
See Chapter 13 Input/Output (I/O) Ports and Chapter 3 Analog-to-Digital Converter (ADC).
1.5.10 Port C I/O Pins (PTC6–PTC0/CAN_TX)
PTC6 and PTC5 are general-purpose, bidirectional I/O port pins.
PTC4–PTC0 are general-purpose, bidirectional I/O port pins that contain higher current sink/source
capability. PTC6–PTC2 are only available on the 48-pin LQFP and 64-pin QFP packages. See
Chapter 13 Input/Output (I/O) Ports.
PTC1 and PTC0 can be programmed to be MSCAN08 pins.
These port pins also have selectable pullups when configured for input mode. The pullups are disengaged
when configured for output mode. The pullups are selectable on an individual port bit basis.
MC68HC08GZ32 Data Sheet, Rev. 3
Freescale Semiconductor
25