M16C29 Datasheet, PDF (26/499 Pages) Renesas Technology Corp – RENESAS MCU M16C FAMILY / M16C/Tiny SERIES

M16C/29 Group
1. Overview
1.1.2 Specifications
Table 1.1 lists performance overview of M16C/29 Group 80-pin package.
Table 1.2 lists performance overview of M16C/29 Group 64-pin package.
Table 1.1 Performance Overview of M16C/29 Group (T-ver./V-ver.) (80-Pin Package)
Item
Performance
CPU
Number of basic instructions 91 instructions
Shortest instruction
50 ns (f(BCLK) = 20MHZ, VCC = 3.0 to 5.5 V) (Normal-ver./T-ver.)
excution time
100 ns(f(BCLK) = 10MHZ, VCC = 2.7 to 5.5 V) (Normal-ver.)
50 ns (f(BCLK) = 20MHZ, VCC = 4.2 to 5.5 V, -40 to 105°C) (V-ver.)
62.5 ns (f(BCLK) = 16MHZ, VCC = 4.2 to 5.5 V, -40 to 125°C) (V-ver.)
Operation mode
Single chip mode
Address space
1 Mbyte
Memory capacity
ROM/RAM: See Tables 1.3 to 1.5
Peripheral Port
Input/Output: 71 lines
Function Multifunction timer
TimerA:16 bits x 5 channels, TimerB:16 bits x 3 channels
Three-phase Motor Control Timer
TimerS (Input Capture/Output Compare):
16 bit base timer x 1 channel (Input/Output x 8 channels)
Serial I/O
2 channels (UART, clock synchronous serial I/O)
1 channel (UART, clock synchronous serial I/O, I²C bus, or IEbus⁽¹⁾)
2 channels (Clock synchronous serial I/O)
1 channel (Multi- master I²C bus)
A/D converter
10 bits x 27 channels
DMAC
2 channels
CRC calculation circuit
2 polynomial (CRC-CCITT and CRC-16) with MSB/LSB selectable
CAN module
1 channel, supporting CAN 2.0B specification
Watchdog timer
15 bits x 1 channel (with prescaler)
Interrupt
29 internal and 8 external sources, 4 software sources,
interrupt priority level: 7
Clock generation circuit
4 circuits
•
•
Main clock
Sub-clock



(These circuits contain a built-in feedback
resistor)
• On-chip oscillator(main-clock oscillation stop detect function)
• PLL frequency synthesizer
Oscillation stop detect Function Main clock oscillation stop, re-oscillation detect function
Voltage detection circuit
Available (Normal-ver.) / Not available (T-ver., V-ver.)
Electrical Power supply voltage
Charact-
eristics
VCC = 3.0 to 5.5 V (f(BCLK) = 20 MHz) (Normal-ver.)
VCC = 2.7 to 5.5 V (f(BCLK) = 10 MHz)
VCC = 3.0 to 5.5 V (T-ver.)
Power consumption
VCC = 4.2 to 5.5 V (V-ver.)
18 mA (VCC = 5 V, f(BCLK) = 20 MHz)
25 µA (f(XCIN) = 32 kHz on RAM)
3 µA (VCC = 5 V, f(XCIN) = 32 kHz, in wait mode)
0.8 µA (VCC = 5 V, in stop mode)
Flash Program/erase supply voltage
2.7 to 5.5 V (Normal-ver.), 3.0 to 5.5V (T-ver.), 4.2 to 5.5 V (V-ver.)
memory Program and erase endurance
Operating ambient temperature
100 times (all space) or 1,000 times (blocks 0 to 5)/
10,000 times (blocks A and B⁽²⁾)
-20 to 85°C/-40 to 85°C⁽²⁾ (Normal-ver.)
-40 to 85°C (T-ver.), -40 to 125°C (V-ver.)
Package
80-pin plastic mold LQFP
NOTES:
1. IEBus is a trademark of NEC Electronics Corporation.
2. Refer to Table 1.6 to Table 1.8 Product code.
Rev. 1.12 Mar.30, 2007
REJ09B0101-0112
page 2 _{of 458}