CP3BT23 Datasheet, PDF (59/260 Pages) Texas Instruments – CP3BT23 Reprogrammable Connectivity Processor with Bluetooth and Dual CAN Interfaces

12.0 Power Management
The Power Management Module (PMM) improves the effi- * The Analog/Digital Converter (ADC) module is not auto-
ciency of the CP3BT23 by changing the operating mode matically disabled by entering Halt mode, however its clock
(and therefore the power consumption) according to the re- is stopped so no conversions may be performed in Halt
quired level of device activity. The device implements four mode. For maximum power savings, software must disable
power modes:
the ADC module before entering Halt mode.
! Active
! Power Save
! Idle
! Halt
A module shown as On/Off in Table 25 may be enabled or
disabled by software. A module shown as Active continues
to operate even while its clock is suspended, which allows
wake-up events to be processed during Idle and Halt
Table 24 summarizes the differences between power ^modes.
modes: the state of the high-frequency oscillator (on or off), The Random Number Generator (RNG) module has two os-
the System Clock source (clock used by most modules), cillators which operate independently of the rest of the sys-
and the clock source used by the Timing and Watchdog tem. For maximum power savings, software must disable
Module (TWM). The high-frequency oscillator generates the
12-MHz Main Clock, and the low-frequency oscillator gener-
ates a 32.768 kHz clock. The Slow Clock can be driven by
the 32.768 kHz clock or a scaled version of the Main Clock.
Table 24 Power Mode Operating Summary
te ^Mode
High-Frequency
Oscillator
System
Clock
TWM Clock
Active
On
Power Save On or Off
Idle
On or Off
le ^Halt
Off
Main Clock Slow Clock
Slow Clock Slow Clock
None
Slow Clock
None
None
The low-frequency oscillator continues to operate in all four
modes and power must be provided continuously to the de-
vice power supply pins. In Halt mode, however, Slow Clock
does not toggle, and as a result, the TWM timer and Watch-
o ^{dog Module do not operate. For the Power Save and Idle}
modes, the high-frequency oscillator can be turned on or off
under software control, as long as the low-frequency oscil-
lator is used to drive Slow Clock.
s Table 25 shows the clock sources used by the CP3BT23 de-
vice modules and their behavior in each power mode.
Table 25 Module Activity Summary
bPower Mode
Module
Active
Power
Save
Idle
Halt
Clock
Source
these oscillators.
12.1 ACTIVE MODE
In Active mode, the high-frequency oscillator is active and
generates the 12-MHz Main Clock. The 32.768 kHz oscilla-
tor is active and may be used to generate the Slow Clock.
The PLL can be active or inactive, as required. Most on-chip
modules are driven by the System Clock. The System Clock
can be the PLL Clock after a programmable divider or the
12-MHz Main Clock. The activity of peripheral modules is
controlled by their enable bits.
Power consumption can be reduced in this mode by selec-
tively disabling modules and by executing the WAIT instruc-
tion. When the WAIT instruction is executed, the CPU stops
executing new instructions until it receives an interrupt sig-
nal. After reset, the CP3BT23 is in Active Mode.
12.2 POWER SAVE MODE
In Power Save mode, Slow Clock is used as the System
Clock which drives the CPU and most on-chip modules. If
Slow Clock is driven by the 32.768 kHz oscillator and no on-
chip module currently requires the 12-MHz Main Clock, soft-
ware can disable the high-frequency oscillator to further re-
duce power consumption. Auxiliary Clocks 1 and 2 can be
turned off under software control before switching to a re-
duced power mode, or they may remain active as long as
Main Clock is also active. If the system does not require the
PLL output clock, the PLL can be disabled. Alternatively, the
Main Clock and the PLL can also be controlled by the Hard-
ware Clock Control function, if enabled. The clock architec-
ture is described in Section 11.0.
O ^CPU
On On/Off Off Off System ^{The Bluetooth LLC can either be switched to the 32 kHz}
clock internally in the module, or it remains running off Aux-
MIWU
On On Active Active System _{iliary clock 1 as long as the Main Clock and Auxiliary Clock}
PMM
On On On Active Slow Clock ^{1 are enabled.}
TWM
Bluetooth
On On On Off Slow Clock ^{In Power Save mode, some modules are disabled or their}
operation is restricted. Other modules, including the CPU,
On/Off On/Off On/Off Off Aux 1 Clock _{continue to function normally, but operate at a reduced clock}
AAI
On/Off On/Off On/Off Off Aux 1 Clock ^{rate. Details of each module’s activity in Power Save mode}
are described in each module’s descriptions.
CVSD/PCM On/Off On/Off On/Off Off Aux 2 Clock
It is recommended to keep CPU activity at a minimum by ex-
ADC
On/Off On/Off On/Off Off* Aux 2 Clock _{ecuting the WAIT instruction to guarantee low power con-}
All Others On/Off On/Off Off Off System ^{sumption in the system.}
www.national.com
58