CP3BT23 Datasheet, PDF (50/260 Pages) Texas Instruments – CP3BT23 Reprogrammable Connectivity Processor with Bluetooth and Dual CAN Interfaces

10.3.4 Interrupt Enable and Mask Register 0 (IENAM0) 10.3.7 Interrupt Status Register 0 (ISTAT0)
The IENAM0 register is a word-wide read/write register
which holds bits that individually enable and disable the
maskable interrupt sources IRQ1 through IRQ15. The reg-
ister is initialized to FFFFh at reset.
The ISTAT0 register is a word-wide read-only register. It in-
dicates which maskable interrupt inputs to the ICU are ac-
tive. These bits are not affected by the state of the
corresponding IENA bits.
15
1
0
15
IENA
Res.
IST
1
0
Res.
IENA
Each Interrupt Enable bit enables or disables IST
The Interrupt Status bits indicate if a
the corresponding interrupt request IRQ1
maskable interrupt source is signalling an in-
through IRQ15, for example IENA15 controls
terrupt request. IST15:1 correspond to IRQ15
IRQ15. Because IRQ0 is not used, IENA0 is
to IRQ1 respectively. Because the IRQ0 inter-
ignored.
0 – Interrupt is disabled.
1 – Interrupt is enabled.
rupt is not used, bit 0 always reads back 0.
0 – Interrupt is not active.
1 – Interrupt is active.
10.3.5 Interrupt Enable and Mask Register 1 (IENAM1) 10.3.8 Interrupt Status Register 1 (ISTAT1)
The IENAM1 register is a word-wide read/write register
which holds bits that individually enable and disable the
te ^{maskable interrupt sources IRQ16 through IRQ31. The reg-}
ister is initialized to FFFFh at reset.
The ISTAT1 register is a word-wide read-only register. It in-
dicates which maskable interrupt inputs into the ICU are ac-
tive. These bits are not affected by the state of the
corresponding IENA bits.
15
0
15
0
IENA
IST
ole ^IENA
Each Interrupt Enable bit enables or disables IST
the corresponding interrupt request IRQ16
through IRQ31, for example IENA31 controls
IRQ31.
0 – Interrupt is disabled.
1 – Interrupt is enabled.
The Interrupt Status bits indicate if a
maskable interrupt source is signalling an in-
terrupt request. IST31:16 correspond to
IRQ31 to IRQ16, respectively.
0 – Interrupt is not active.
1 – Interrupt is active.
10.3.6 Interrupt Enable and Mask Register 2 (IENAM2) 10.3.9 Interrupt Status Register 2 (ISTAT2)
The IENAM2 register is a word-wide read/write register
s which holds bits that individually enable and disable the
maskable interrupt sources IRQ32 through IRQ47. The reg-
ister is initialized to FFFFh at reset.
The ISTAT2 register is a word-wide read-only register. It in-
dicates which maskable interrupt inputs into the ICU are ac-
tive. These bits are not affected by the state of the
corresponding IENA bits.
b ₁₅
0
15
0
IENA
IST
O ^IENA
Each Interrupt Enable bit enables or disables IST
The Interrupt Status bits indicate if a
the corresponding interrupt request IRQ32
maskable interrupt source is signalling an in-
through IRQ47, for example IENA47 controls
terrupt request. IST47:32 correspond to
IRQ47.
IRQ47 to IRQ32, respectively.
0 – Interrupt is disabled.
0 – Interrupt is not active.
1 – Interrupt is enabled.
1 – Interrupt is active.
49
www.national.com