LAN9311 Datasheet, PDF (302/461 Pages) SMSC Corporation – Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
14.4.2.9 Port x PHY Special Modes Register (PHY_SPECIAL_MODES_x)
Index (decimal): 18
Size:
16 bits
This read/write register is used to control the special modes of the Port x PHY.
Note: This register is re-written by the EEPROM Loader following the release of reset or a RELOAD
command. Refer to Section 10.2.4, "EEPROM Loader," on page 150 for more information.
BITS
15:8
7:5
4:0
DESCRIPTION
RESERVED
PHY Mode (MODE[2:0])
This field controls the PHY mode of operation. Refer to Table 14.10 for a
definition of each mode.
PHY Address (PHYADD)
The PHY Address field determines the MMI address to which the PHY will
respond and is also used for initialization of the cipher (scrambler) key. Each
PHY must have a unique address. Refer to Section 7.1.1, "PHY
Addressing," on page 82 for additional information.
Note:
No check is performed to ensure that this address is unique from
the other PHY addresses (Port 1 PHY, Port 2 PHY, and Virtual
PHY).
TYPE
RO
R/W
NASR
Note 14.58
R/W
NASR
Note 14.58
DEFAULT
-
Note 14.59
Note 14.60
Note 14.58 Register bits designated as NASR are reset when the Port x PHY Reset is generated via
the Reset Control Register (RESET_CTL). The NASR designation is only applicable when
the Reset (PHY_RST) bit of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x) is set.
Note 14.59 The default value of this field is determined by a combination of the configuration straps
autoneg_strap_x, speed_strap_x, and duplex_strap_x. If the autoneg_strap_x is 1, then
the default MODE[2:0] value is 111b. Else, the default value of this field is determined by
the remaining straps. MODE[2]=0, MODE[1]=(speed_strap_1 for Port 1 PHY,
speed_strap_2 for Port 2 PHY), and MODE[0]=(duplex_strap_1 for Port 1 PHY,
duplex_strap_2 for Port 2 PHY). Configuration strap values are latched upon the de-
assertion of a chip-level reset as described in Section 4.2.4, "Configuration Straps," on
page 40. Refer to Section 4.2.4, "Configuration Straps," on page 40 for configuration strap
definitions.
Note 14.60 The default value of this field is determined by the phy_addr_sel_strap configuration strap.
Refer to Section 7.1.1, "PHY Addressing," on page 82 for additional information.
Table 14.10 MODE[2:0] Definitions
AFFECTED REGISTER BIT VALUES
MODE[2:0]
MODE DEFINITIONS
PHY_BASIC_CONTROL_x
PHY_AN_ADV_x
000
10BASE-T Half Duplex. Auto-negotiation disabled.
001
10BASE-T Full Duplex. Auto-negotiation disabled.
010
100BASE-TX Half Duplex. Auto-negotiation
disabled. CRS is active during Transmit & Receive.
[13,12,10,8]
0000
0001
1000
[8,7,6,5]
N/A
N/A
N/A
Revision 2.0 (02-14-13)
302
DATASHEET
SMSC LAN9311/LAN9311i