English
Language : 

JDP2S01T Datasheet, PDF (131/150 Pages) Toshiba Semiconductor – UHF~VHF Band RF Attenuator Applications
◁
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Table 146: Static characteristics: analog I/O pins (D+, D−)[1]
VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Input levels
VDI
differential input sensitivity
|VI(D+) − VI(D−)|
VCM
differential common mode
includes VDI range
voltage
0.2
-
0.8
-
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
Output levels
-
-
2.0
-
VOL
LOW-level output voltage
RL = 1.5 kΩ to +3.6 V
-
-
VOH
HIGH-level output voltage
RL = 15 kΩ to GND
2.8
-
Leakage current
ILZ
OFF-state leakage current
Capacitance
−10
-
CIN
transceiver capacitance
Resistance
pin to GND
-
-
Rpd(OTG)
pull-down resistance on
enable internal
pins OTG_DP1 and OTG_DM1 resistors
14.25
-
Rpd(H)
pull-down resistance on
pins H_DP2 and H_DM2
enable internal
resistors
10
-
Rpu(OTG)
pull-up resistance on
OTG_DP1
bus idle
bus driven
900
-
1 425
-
ZDRV
driver output impedance
steady-state drive
[2] 29
-
ZINP
input impedance
10
-
Termination
VTERM
termination voltage for
upstream port pull up (RPU)
[3] 3.0
-
Max
Unit
-
V
2.5
V
0.8
V
-
V
0.3
V
3.6
V
+10
µA
10
pF
24.8
kΩ
20
kΩ
1575
Ω
3 090
Ω
44
Ω
-
MΩ
3.6
V
[1] DP represents OTG_DP1 and H_DP2, and DM represents OTG_DM1 and H_DM2. D+ is the USB positive data line and D− is the USB
negative data line.
[2] Includes external resistors of 18 Ω ± 10% on H_DP2 and H_DM2, and 27 Ω ± 10% on OTG_DP1 and OTG_DM1.
[3] In the suspend mode, the minimum voltage is 2.7 V.
Table 147: Static characteristics: charge pump
VCC = 3.0 V to 3.6 V; GND = 0 V; Tamb = −40 °C to +85 °C; CLOAD = 2 µF; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VBUS
regulated VBUS voltage
ILOAD = 8 mA from
-
VBUS(OTG); see Figure 29
5
5.25
V
ILOAD
maximum load current
external capacitor of 27 nF; -
-
8
mA
VCC = 3.0 V to 3.6 V
external capacitor of 82 nF; -
-
14
mA
VCC = 3.0 V to 3.3 V
external capacitor of 82 nF; -
-
20
mA
VCC = 3.3 V to 3.6 V
CLOAD
output capacitance
1
-
6.5
µF
VBUS(LEAK)
VBUS(OTG) leakage voltage VBUS(OTG) not driven
-
-
0.2
V
9397 750 12337
Product data
Rev. 03 — 06 January 2004
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
131 of 150
 ▷