M16C62_M Datasheet, PDF (300/615 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

Electrical characteristics
Mitsubishi microcomputers
M16C / 62M Group
(Low voltage version)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table 1.31.3. Electrical characteristics (referenced to VCC = 2.7V to 3.6V, VSS = 0V at Topr = – 20^oC to
85^oC / – 40^oC to 85^oC (Note 1), f(XIN) = 10MHZ without wait unless otherwise specified)
Symbol
VO H
HIGH output
voltage
Parameter
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
P40 to P47, P50 to P57, P60 to P67, P72 to P77,
P80 to P84, P86,P87, P90 to P97, P100 to P107
Measuring condition
IOH=–1mA
Standard
Min Typ. Max.
Unit
2.5
V
VO H
VO L
VO L
HIGH output
voltage
HIGH output
voltage
LOW output
voltage
LOW output
voltage
LOW output
voltage
XOUT
HIGHPOWER
LOWPOWER
XCOUT
HIGHPOWER
LOWPOWER
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
P40 to P47, P50 to P57, P60 to P67, P70 to P77,
P80 to P84, P86,P87, P90 to P97, P100 to P107
XOUT
HIGHPOWER
LOWPOWER
XCOUT
HIGHPOWER
LOWPOWER
IOH=–0.1mA
IOH=–50µA
With no load applied
With no load applied
IOL=1mA
IOL=0.1mA
IOL=50µA
With no load applied
With no load applied
2.5
2.5
V
3.0
V
1.6
0.5
V
0.5
V
0.5
0
V
0
VT+–VT–
Hysteresis
HOLD, RDY, TA0IN to TA4IN, TB0IN to TB5IN,
INT0 to INT5, NMI, ADTRG, CTS0 to CTS2, SCL,
SDA, CLK0 to CLK4, TA2OUT to TA4OUT,
KI0 to KI3, RxD0 to RxD2, SIN3, SIN4
0.2
0.8
V
VT+–VT–
IIH
Hysteresis
HIGH input
current
RESET
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
P40 to P47, P50 to P57, P60 to P67, P70 to P77,
P80 to P87, P90 to P97, P100 to P107,
XIN, RESET, CNVss, BYTE
VI=3V
0.2
1.8
V
4.0 µA
LOW input
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
II L
current
P40 to P47, P50 to P57, P60 to P67, P70 to P77,
P80 to P87, P90 to P97, P100 to P107,
VI=0V
XIN, RESET, CNVss, BYTE
–4.0 µA
RPULLUP
Pull-up
resistance
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
P40 to P47, P50 to P57, P60 to P67, P72 to P77,
P80 to P84, P86,P87, P90 to P97, P100 to P107
VI=0V
20 75 330 kΩ
RfXIN
RfXCIN
VRAM
Feedback resistance
Feedback resistance
XIN
XCIN
RAM retention voltage
When clock is stopped
In single-chip mode, the output pins
are open and other pins are VSS
Mask ROM version
Flash memory
3V version
f(XIN)=10MHz
Square wave,
no division
f(XIN)=10MHz
Square wave,
no division
Mask ROM version,
flash memory
f(XCIN)=32kHz
3V version
Square wave
3.0
MΩ
10.0
MΩ
2.0
V
9.5 21.25 mA
12.0 21.25 mA
45.0
µA
Flash memory
3V version
program
f(XIN)=10MHz
Square wave,
division by 2
14.0
mA
ICC
Power supply current
Flash memory
3V version
erase
f(XIN)=10MHz
Square wave,
division by 2
17.0
mA
Mask ROM version, ^{f(XCIN)=32kHz}
flash memory
When a WAIT instruction
2.8
µA
3V version
is executed.
Oscillation capacity High
(Note 2)
f(XCIN)=32kHz
When a WAIT instruction
is executed.
0.9
µA
Oscillation capacity Low
(Note 2)
When clock is stopped
Topr=25°C
When clock is stopped
Topr=85°C
1.0
µA
20.0
Note 1: Specify a product of -40°C to 85°C to use it.
Note 2: With one timer operated using fC32.
1-281