M16C62_M Datasheet, PDF (208/615 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

Electrical characteristics (Vcc = 3V)
Mitsubishi microcomputers
M16C / 62A Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
VCC = 3V
Table 1.23.23. Electrical characteristics (referenced to VCC = 2.7 to 3.3V, VSS = 0V at Topr = – 20^oC
to 85^oC / – 40^oC to 85^oC (Note 1), f(XIN) = 10MHZ (Note 2) with wait unless otherwise
specified)
Symbol
Parameter
Measuring condition
VOH
VOH
VOL
VOL
VT+-VT-
VT+-VT-
IIH
HIGH output P00 to P07, P10 to P17, P20 to P27,
voltage
P30 to P37, P40 to P47, P50 to P57,
P60 to P67, P72 to P77, P80 to P84,
P86, P87, P90 to P97, P100 to P107
IOH = -1mA
HIGH output voltage XOUT
HIGHPOWER
LOWPOWER
IOH = -0.1mA
IOH = -50µA
HIGH output voltage XCOUT
HIGHPOWER
LOWPOWER
With no load applied
With no load applied
LOW output P00 to P07 ,P10 to P17, P20 to P27,
voltage
P30 to P37, P40 to P47, P50 to P57,
P60 to P67, P70 to P77, P80 to P84,
P86, P87, P90 to P97, P100 to P107
IOL = 1mA
LOW output voltage XOUT
HIGHPOWER
LOWPOWER
IOL = 0.1mA
IOL = 50µA
LOW output voltage XCOUT
HIGHPOWER
LOWPOWER
With no load applied
With no load applied
Hysteresis
HOLD, RDY, TA0IN to TA4IN,
TB0IN to TB5IN, INT0 to INT5, NMI,
ADTRG, CTS0 to CTS2, SCL, SDA
CLK0 to CLK4,TA2OUT to TA4OUT,
KI0 to KI3, RxD0 to RxD2, SIN3, SIN4
Hysteresis RESET
HIGH input
current
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47 ,P50 to P57,
P60 to P67, P70 to P77, P80 to P87,
P90 to P97, P100 to P107,
XIN, RESET, CNVss, BYTE
VI = 3V
Standard
Min Typ. Max. ^Unit
2.5
V
2.5
2.5
V
3.0
V
1.6
0.5
V
0.5
V
0.5
0
V
0
0.2
0.8
V
0.2
1.8
V
4.0
µA
LOW input P00 to P07, P10 to P17, P20 to P27,
current
P30 to P37, P40 to P47, P50 to P57,
I IL
P60 to P67, P70 to P77, P80 to P87, VI = 0V
P90 to P97, P100 to P107,
XIN, RESET, CNVss, BYTE
-4.0
µA
R PULLUP
Pull-up
resistance
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P67, P72 to P77, P80 to P84,
P86, P87, P90 to P97 ,P100 to P107
VI = 0V
R fXIN
R fXCIN
V RAM
Feedback resistance XIN
Feedback resistance XCIN
RAM retention voltage
When clock is stopped
In single-chip
mode, the
output pins are
open and other
pins are VSS
Mask ROM
version
Flash memory
5V version
Mask ROM
version
f(XIN) = 10MHz
Square wave, no division
f(XIN) = 10MHz
Square wave, no division
f(XCIN) = 32kHz
Square wave
Flash memory
5V version
f(XCIN) = 32kHz
Square wave, in RAM
Icc
Power supply current
Flash memory
5V version
f(XCIN) = 32kHz
Square wave, in flash memory
f(XCIN) = 32kHz
When a WAITinstruction
is executed.
Oscillation capacity High
(Note 3)
f(XCIN) = 32kHz
When a WAIT instruction
is executed.
Oscillation capacity Low
(Note 3)
Topr = 25°C
when clock is stopped
Topr = 85°C
when clock is stopped
Note 1: Specify a product of -40°C to 85°C to use it.
Note 2: 10 MHz for the mask ROM version and flash memory 5V version.
Note 3: With one timer operated using fC32.
66.0 120.0 500.0 kΩ
3.0
MΩ
10.0
MΩ
2.0
V
8.5 21.25 mA
12.0 21.25 mA
40.0
µA
40.0
µA
800
µA
10
2.8 (Topr
µA
= 25°C)
10
0.9 (Topr
µA
= 25°C)
1.0
µA
20.0
1-189