M16C62_M Datasheet, PDF (195/615 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

Electrical characteristics (Vcc = 5V)
Mitsubishi microcomputers
M16C / 62A Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
VCC = 5V
Table 1.23.3. A-D conversion characteristics (referenced to VCC = AVCC = VREF = 2.7V to 5.5V, Vss = AVSS =
0V at Topr = – 20^oC to 85^oC / – 40^oC to 85^oC (Note 4) unless otherwise specified)
Symbol
Parameter
Resolution
Absolute Sample & hold function not available
accuracy
Sample & hold function available(10bit)
Measuring condition
VREF = VCC
VREF = VCC = 5V
AN0 to AN7 input
VREF =VCC _{ANEX0, ANEX1 input,}
= 5V
External op-amp connection mode
Standard
Min. Typ. Max.
10
±3
±3
±7
Unit
Bits
LSB
LSB
LSB
RLADDER
tCONV
tCONV
tCONV
tSAMP
VREF
VIA
Sample & hold function available(8bit)
VREF = VCC = 5V
Sample & hold function not available(8bit) VREF = VCC = 3V, ØAD = fAD/2
Ladder resistance
VREF = VCC
10
Conversion time(10bit), Sample & hold function available
Conversion time(8bit), Sample & hold function available
VREF = VCC = 5V, ØAD =10MHz
VREF = VCC = 5V, ØAD =10MHz
3.3
2.8
Conversion time(8bit), Sample & hold function not available
Sampling time
VREF = VCC = 3V, ØAD = fAD/2 = 5MHz 9.8
0.3
Reference voltage
2.7
Analog input voltage
0
±2
±2
40
VCC
VREF
LSB
LSB
kΩ
µs
µs
µs
µs
V
V
Note 1: Do f(X IN) in range of main clock input oscillation frequency prescribed with recommended operating
conditions of table 1.23.2. Divide the f AD if f(XIN) exceeds 10MHz, and make AD operation clock frequency
(ØAD) equal to or lower than 10MHz. And divide the f AD if VCC is less than 4.2V, and make AD operation
clock frequency (ØAD) equal to or lower than f AD/2.
Note 2: A case without sample & hold function turn AD operation clock frequency (ØAD) into 250 kHz or more in
addition to a limit of Note 1.
A case with sample & hold function turn AD operation clock frequency (ØAD) into 1MHz or more in addition
to a limit of Note 1.
Note 3: Connect AV CC pin to VCC pin and apply the same electric potential.
Note 4: Specify a product of -40°C to 85°C to use it.
Table 1.23.4. D-A conversion characteristics (referenced to VCC = VREF = 2.7V to 5.5V, VSS = AVSS
= 0V, at Topr = – 20^oC to 85^oC / – 40^oC to 85^oC (Note 2) unless otherwise specified)
Symbol
Parameter
Measuring condition
Standard
Min. Typ. Max. ^Unit
tsu
RO
IVREF
Resolution
Absolute accuracy
Setup time
Output resistance
Reference power supply input current
(Note 1)
8 Bits
1.0 %
3 µs
4 10 20 kΩ
1.5 mA
Note 1: This applies when using one D-A converter, with the D-A register for the unused D-A converter set to
“0016”.
The A-D converter's ladder resistance is not included.
Also, when D-A register contents are not “00 16”, the current IVREF always flows even though Vref may
have been set to be unconnected by the A-D control register.
Note 2: Specify a product of -40°C to 85°C to use it.
Table 1.23.5. Flash memory version electrical characteristics
(referenced to VCC = 4.2V to 5.5V, at Topr =0 to 60^oC unless otherwise specified)
Parameter
Standard
Min.
Typ.
Max
Unit
Page program time
6
120
ms
Block erase time
50
600
ms
Erase all unlocked blocks time
50 X n (Note) 600 X n (Note) ms
Lock bit program time
6
120
ms
Note : n denotes the number of block erases.
1-176