M16C62_M Datasheet, PDF (175/615 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

A-D Converter
Mitsubishi microcomputers
M16C / 62A Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(4) Repeat sweep mode 0
In repeat sweep mode 0, the pins selected using the A-D sweep pin select bit are used for repeat sweep
A-D conversion. Table 1.17.5 shows the specifications of repeat sweep mode 0. Figure 1.17.7 shows the
A-D control register in repeat sweep mode 0.
Table 1.17.5. Repeat sweep mode 0 specifications
Item
Specification
Function
Start condition
The pins selected by the A-D sweep pin select bit are used for repeat A-D conversion
Writing “1” to A-D conversion start flag
Stop condition
Writing “0” to A-D conversion start flag
Interrupt request generation timing None generated
Input pin
AN0 and AN1 (2 pins), AN0 to AN3 (4 pins), AN0 to AN5 (6 pins), or AN0 to AN7 (8 pins)
Reading of result of A-D converter Read A-D register corresponding to selected pin (at any time)
A-D control register 0 (Note)
b7 b6 b5 b4 b3 b2 b1 b0
11
Symbol
ADCON0
Address When reset
03D616 00000XXX2
Bit symbol
Bit name
CH0
Analog input pin
select bit
CH1
Function
Invalid in repeat sweep mode 0
RW
CH2
MD0
MD1
A-D operation mode
select bit 0
b4 b3
1 1 : Repeat sweep mode 0
TRG
ADST
Trigger select bit
A-D conversion start flag
0 : Software trigger
1 : ADTRG trigger
0 : A-D conversion disabled
1 : A-D conversion started
CKS0
Frequency select bit 0
0 : fAD/4 is selected
1 : fAD/2 is selected
Note: If the A-D control register is rewritten during A-D conversion, the conversion result
is indeterminate.
A-D control register 1 (Note 1)
b7 b6 b5 b4 b3 b2 b1 b0
1
0
Symbol
ADCON1
Address
03D716
When reset
0016
Bit symbol
Bit name
Function
RW
SCAN0
SCAN1
MD2
A-D sweep pin select bit
A-D operation mode
select bit 1
When single sweep and repeat sweep mode 0
are selected
b1 b0
0 0 : AN0, AN1 (2 pins)
0 1 : AN0 to AN3 (4 pins)
1 0 : AN0 to AN5 (6 pins)
1 1 : AN0 to AN7 (8 pins)
Set to “0” when this mode is selected
BITS
8/10-bit mode select bit 0 : 8-bit mode
1 : 10-bit mode
CKS1
Frequency select bit 1
0 : fAD/2 or fAD/4 is selected
1 : fAD is selected
VCUT Vref connect bit
1 : Vref connected
OPA0
OPA1
External op-amp
connection mode
bit (Note 2)
b7 b6
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion result
is indeterminate.
Note 2: Neither “01” nor “10” can be selected with the external op-amp connection mode bit.
Figure 1.17.7. A-D conversion register in repeat sweep mode 0
1-156