M30222 Datasheet, PDF (160/237 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

deUvnedloepr ^ment
Specifications in this manual are tentative and subject to change
MITSUBISHI MICROCOMPUTERS
M30222 Group
Rev. G
A-D Converter
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(1) One-shot mode
In one-shot mode, the pin selected using the analog input pin select bit is used for one-shot A-D
conversion. Table 1.50 shows the specifications of one-shot mode. Figure 1.129 shows the A-D con-
trol register in one-shot mode.
Table 1.50. One-shot mode specifications
Item
Function
Start condition
Stop condition
Interrupt request
generation timing
Input pin
Reading A-D
converter results
Specification
The pin selected by the analog input pin select bit is used for one-shot A-D conversion
Writing 1 to A-D conversion start flag
Writing 0 to A-D conversion start flag
End of A-D conversion (A-D conversion start flag changes ot 0 , except when exter-
nal trigger is selected).
End of A-D conversion
One of AN₀ to AN₇ as selected
Read A-D register corresponding to selected pin
A-D control register 0 (Note 1)
b7 b6 b5 b4 b3 b2 b1 b0
00
Symbol
ADCON0
Address
03D616
When reset
00000XXX 2
Bit symbol
Bit name
Function
RW
CH0
CH1
CH2
Analog input pin select
bit
b2 b1 b0
0 0 0 : AN 0 is selected
0 0 1 : AN 1 is selected
0 1 0 : AN 2 is selected
0 1 1 : AN 3 is selected
1 0 0 : AN 4 is selected
1 0 1 : AN 5 is selected
1 1 0 : AN 6 is selected
1 1 1 : AN 7 is selected
(Note 2)
MD0
MD1
TRG
ADST
CKS0
A-D operation mode
select bit 0
Trigger select bit
A-D conversion start flag
Frequency select bit 0
b4 b3
0 0 : One-shot mode
0 : Software trigger
1 : ADTRG trigger
0 : A-D conversion disabled
1 : A-D conversion started
0: fAD/4 is selected
1: fAD/2 is selected
(Note 2)
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion
result is indeterminate.
Note 2: When changing A-D operation mode, set analog input pin again.
A-D control register 1 (Note)
b7 b6 b5 b4 b3 b2 b1 b0
1
0
Symbol
ADCON1
Address
03D716
When reset
0016
Bit symbol
Bit name
SCAN0
SCAN1
A-D sweep pin
select bit
Function
Invalid in one-shot mode
RW
MD2
BITS
CKS1
A-D operation mode
select bit 1
8/10-bit mode select bit
Frequency select bit1
0 : Any mode other than repeat sweep
mode 1
0 : 8-bit mode
1 : 10-bit mode
0 : fAD/2 or fAD/4 is selected
1 : fAD is selected
VCUT Vref connect bit
1 : Vref connected
OPA0
OPA1
External op-amp
connection mode bit
b7 b6
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
Note: If the A-D control register is rewritten during A-D conversion, the conversion
result is indeterminate.
Figure 1.129. A-D conversion register in one-shot mode
1-161