M30222 Datasheet, PDF (109/237 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

deUvnedloepr ^ment
Specifications in this manual are tentative and subject to change
MITSUBISHI MICROCOMPUTERS
M30222 Group
Rev. G
Serial Communications
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
UARTi transmit/receive control register 0
b7 b6 b5 b4 b3 b2 b1 b0
Symbol
UiC0(i=0,1)
Address
03A416, 03AC16
When reset
0816
Bit
symbol
Bit name
CLK0
CLK1
BRG count source
select bit
Function
(During clock synchronous
serial I/O mode)
b1 b0
0 0 : f1 is selected
0 1 : f8 is selected
1 0 : f32 is selected
1 1 : Inhibited
Function
(During UART mode)
b1 b0
0 0 : f1 is selected
0 1 : f8 is selected
1 0 : f32 is selected
1 1 : Inhibited
RW
CRS
TXEPT
CTS/RTS function
select bit
Transmit register empty
flag
Valid when bit 4 = “0”
0 : CTS function is selected (Note 1)
1 : RTS function is selected (Note 2)
0 : Data present in transmit
register (during transmission)
1 : No data present in transmit
register (transmission
completed)
Valid when bit 4 = “0”
0 : CTS function is selected (Note 1)
1 : RTS function is selected (Note 2)
0 : Data present in transmit register
(during transmission)
1 : No data present in transmit
register (transmission completed)
CRD CTS/RTS disable bit
0 : CTS/RTS function enabled
1 : CTS/RTS function disabled
(P60 and P64 function as
programmable I/O port)
0 : CTS/RTS function enabled
1 : CTS/RTS function disabled
(P60 and P64 function as
programmable I/O port)
NCH Data output select bit
0 : TXDi pin is CMOS output
1 : TXDi pin is N-channel
open-drain output
0: TXDi pin is CMOS output
1: TXDi pin is N-channel
open-drain output
CKPOL CLK polarity select bit
0 : Transmit data is output at
falling edge of transfer clock
and receive data is input at
rising edge
1 : Transmit data is output at
rising edge of transfer clock
and receive data is input at
falling edge
Must always be “0”
UFORM Transfer format select bit ^{0 : LSB first}
1 : MSB first
Must always be “0”
Note 1: Set the corresponding port direction register to “0”.
Note 2: The settings of the corresponding port register and port direction register are invalid.
UART2 transmit/receive control register 0 ^{(Note 3)}
b7 b6 b5 b4 b3 b2 b1 b0
Symbol
U2C0
Address
037C16
When reset
0816
Bit
symbol
CLK0
CLK1
CRS
TXEPT
CRD
Bit name
BRG count source
select bit
Function
(During clock synchronous
serial I/O mode)
b1 b0
0 0 : f1 is selected
0 1 : f8 is selected
1 0 : f32 is selected
1 1 : Inhibited
Function
(During UART mode)
b1 b0
0 0 : f1 is selected
0 1 : f8 is selected
1 0 : f32 is selected
1 1 : Inhibited
RW
CTS/RTS function
select bit
Transmit register empty
flag
Valid when bit 4 = “0”
0 : CTS function is selected (Note 1)
1 : RTS function is selected (Note 2)
0 : Data present in transmit
register (during transmission)
1 : No data present in transmit
register (transmission
completed)
Valid when bit 4 = “0”
0 : CTS function is selected (Note 1)
1 : RTS function is selected (Note 2)
0 : Data present in transmit register
(during transmission)
1 : No data present in transmit
register (transmission completed)
CTS/RTS disable bit
0 : CTS/RTS function enabled
1 : CTS/RTS function disabled
(P73 functions
programmable I/O port)
0 : CTS/RTS function enabled
1 : CTS/RTS function disabled
(P73 functions programmable
I/O port)
Nothing is assigned.
Write "0" when writing to this bit. If read, the value is "0".
CKPOL CLK polarity select bit
0 : Transmit data is output at
falling edge of transfer clock
and receive data is input at
rising edge
For SPI, clock is high
between transfers
1 : Transmit data is output at
rising edge of transfer clock
and receive data is input at
falling edge
For SPI, clock is low
between transfers
UFORM ^{Transfer format select bit 0 : LSB first}
1 : MSB first
Must always be “0”
0 : LSB first
1 : MSB first
Note 1: Set the corresponding port direction register to “0”.
Note 2: The settings of the corresponding port register and port direction register are invalid.
Note 3: Only clock synchronous serial I/O mode and 8 bit UART mode are valid.
Fig. 1.83. Serial I/O-related registers (3)
1-110