PIC24FJ128GC010 Datasheet, PDF (434/472 Pages) Microchip Technology – 16-Bit Flash Microcontrollers with 12-Bit Pipeline A/D, Sigma-Delta A/D, USB On-The-Go and XLP Technology

PIC24FJ128GC010 FAMILY
TABLE 37-13: VBAT OPERATING VOLTAGE SPECIFICATIONS
Param
No.
Symbol
Characteristic
Min
Typ Max
DVB01 VBT
Operating Voltage
1.6
—
3.6
Units
V
DVB02
VBATBOR
—
3.6
V
DVB10 VBTADC VBAT A/D Monitoring Voltage
1.6
—
3.6
V
Specification⁽¹⁾
Note 1: Measuring the A/D value using the A/D is represented by the equation:
Measured Voltage = ((VBAT/2)/VDD) * 4096) for 12-bit A/D.
Comments
Battery connected to the
VBAT pin, VBTBOR = 0
Battery connected to the
VBAT pin, VBTBOR = 1
A/D monitoring the VBAT
pin using the internal A/D
channel
TABLE 37-14: CTMU CURRENT SOURCE SPECIFICATIONS
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for Industrial
Param
No.
Sym
Characteristic
Min Typ⁽¹⁾ Max Units
Comments
Conditions
DCT10 IOUT1 CTMU Current
— 550 —
Source, Base Range
nA CTMUICON<1:0> = 00
DCT11 IOUT2 CTMU Current
— 5.5 — A CTMUICON<1:0> = 01
Source, 10x Range
DCT12 IOUT3 CTMU Current
—
55
—
A CTMUICON<1:0> = 10 ^{2.5V < VDD < VDDMAX}
Source, 100x Range
DCT13 IOUT4 CTMU Current
— 550 —
Source, 1000x Range
A CTMUICON<1:0> = 11⁽²⁾
DCT21 V Temperature Diode
— -3 — mV/°C
Voltage Change per
Degree Celsius
Note 1: Nominal value at center point of current trim range (CTMUICON<7:2> = 000000).
2: Do not use this current range with temperature sensing diode.
TABLE 37-15: USB ON-THE-GO MODULE SPECIFICATIONS
DC CHARACTERISTICS
Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for Industrial
Param
No.
Symbol
Characteristic
Min
Typ
Max Units
Conditions
Operating Voltage
DUS01 VUSB3V3 USB Supply Voltage
Greater of:
3.3
3.6
V USB module enabled
3.0 or
(VDD – 0.3V)
(VDD – 0.3V)⁽¹⁾
—
3.6
V USB disabled, RG2/RG3
are unused and externally
pulled low or left in a
high-impedance state
(VDD – 0.3V) VDD
3.6
V USB disabled, RG2/RG3
are used as general
purpose I/O
Note 1: The VUSB pin may also be left in a high-impedance state under these conditions. However, if the voltage
floats below (VDD – 0.3V), this may result in higher IPD currents than specified. The preferred method is to
tie the VUSB pin to VDD, even if the USB module is not used.
DS30009312B-page 434
 2012-2013 Microchip Technology Inc.