|
PIC24FJ128GC010 Datasheet, PDF (33/472 Pages) Microchip Technology – 16-Bit Flash Microcontrollers with 12-Bit Pipeline A/D, Sigma-Delta A/D, USB On-The-Go and XLP Technology | |||
|
◁ |
PIC24FJ128GC010 FAMILY
2.0 GUIDELINES FOR GETTING
STARTED WITH 16-BIT
MICROCONTROLLERS
2.1 Basic Connection Requirements
Getting started with the PIC24FJ128GC010 family
family of 16-bit microcontrollers requires attention to a
minimal set of device pin connections before
proceeding with development.
The following pins must always be connected:
⢠All VDD and VSS pins
(see Section 2.2 âPower Supply Pinsâ)
⢠All analog power pins (AVDD, SVDD, AVSS and
SVSS), regardless of whether or not the analog
device features are used
(see Section 2.2 âPower Supply Pinsâ)
⢠The USB transceiver supply, VUSB3V3, regardless
of whether or not the USB module is used
(see Section 2.2 âPower Supply Pinsâ)
⢠MCLR pin
(see Section 2.3 âMaster Clear (MCLR) Pinâ)
⢠VCAP pin
(see Section 2.4 âVoltage Regulator Pin (VCAP)â)
These pins must also be connected if they are being
used in the end application:
⢠PGECx/PGEDx pins used for In-Circuit Serial
Programming⢠(ICSPâ¢) and debugging purposes
(see Section 2.5 âICSP Pinsâ)
⢠OSCI and OSCO pins when an external oscillator
source is used
(see Section 2.6 âExternal Oscillator Pinsâ)
Additionally, the following pins may be required:
⢠Any voltage reference pins used when external
voltage reference for analog modules is
implemented (AVREF+/AVREF-, CVREF+/CVREF-,
DVREF+ and SVREF+/SVREF-)
Note:
All analog power supply and return pins
must always be connected, regardless of
whether any of the analog modules are
being used.
The minimum mandatory connections are shown in
Figure 2-1.
FIGURE 2-1:
RECOMMENDED
MINIMUM CONNECTIONS
VDD
C2(2)
R1
R2
C1(4)
C6(2)
MCLR
VCAP
PIC24FJXXXX
VSS
VUSB3V3
VDD
VSS
C7(1)
C3(3)
C5(2)
C4(2)
Key (all values are recommendations):
C1 through C6: 0.1 ïF, 20V ceramic
C7: 10 ïF, 6.3V or greater, tantalum or ceramic
R1: 10 kâ¦
R2: 100⦠to 470â¦
Note 1:
2:
3:
4:
See Section 2.4 âVoltage Regulator Pin
(VCAP)â for details on selecting the proper
capacitor for VCAP.
The example shown is for a PIC24F device
with five power and ground pairs (including
analog and USB). Other devices may have
more or less pairs; adjust the number of
decoupling capacitors appropriately.
See Section 19.1 âHardware Configura-
tionâ for details on connecting the pins for
USB operation.
C1 is optional, see Section 2.3 âMaster
Clear (MCLR) Pinâ and Section 2.5 âICSP
Pinsâ for more information.
ï£ 2012-2013 Microchip Technology Inc.
DS30009312B-page 33
|
▷ |