PIC24FJ128GC010 Datasheet, PDF (409/472 Pages) Microchip Technology – 16-Bit Flash Microcontrollers with 12-Bit Pipeline A/D, Sigma-Delta A/D, USB On-The-Go and XLP Technology

PIC24FJ128GC010 FAMILY
34.2 On-Chip Voltage Regulator
All PIC24FJ128GC010 family devices power their core
digital logic at a nominal 1.8V. This may create an issue
for designs that are required to operate at a higher
typical voltage, such as 3.3V. To simplify system
design, all devices in the PIC24FJ128GC010 family
incorporate an on-chip regulator that allows the device
to run its core logic from VDD.
This regulator is always enabled. It provides a constant
voltage (1.8V nominal) to the digital core logic, from a
VDD of 2.0V all the way up to the device’s VDDMAX. It
does not have the capability to boost VDD levels. In
order to prevent “brown-out” conditions when the volt-
age drops too low for the regulator, the Brown-out
Reset occurs. Then the regulator output follows VDD
with a typical voltage drop of 300 mV.
A low-ESR capacitor (such as ceramic) must be
connected to the VCAP pin (Figure 34-1). This helps to
maintain the stability of the regulator. The recommended
value for the filter capacitor (CEFC) is provided in
Section 37.1 “DC Characteristics”.
FIGURE 34-1:
CONNECTIONS FOR THE
ON-CHIP REGULATOR
3.3V⁽¹⁾
PIC24FJXXXGC0XX
CEFC
(10 F typ)
VDD
VCAP
VSS
Note 1:
This is a typical operating voltage. Refer to
Section 37.0 “Electrical Characteristics”
for the full operating ranges of VDD.
34.2.1 ON-CHIP REGULATOR AND POR
The voltage regulator requires a small amount of time
to transition from a disabled or standby state into nor-
mal operating mode. During this time, designated as
TVREG, code execution is disabled. TVREG is applied
every time the device resumes operation after any
power-down, including Sleep mode. TVREG is deter-
mined by the status of the PMSLP bit (RCON<8>).
Refer to Section 37.0 “Electrical Characteristics” for
more information on TVREG.
Note:
For more information, see Section 37.0
“Electrical Characteristics”. The Infor-
mation in this data sheet supersedes the
information in the “PIC24F Family
Reference Manual”.
34.2.2
VOLTAGE REGULATOR STANDBY
MODE
The on-chip regulator always consumes a small incre-
mental amount of current over IDD/IPD, including when
the device is in Sleep mode, even though the core
digital logic does not require power. To provide addi-
tional savings in applications where power resources
are critical, the regulator can be made to enter Standby
mode on its own whenever the device goes into Sleep
mode. This feature is controlled by the PMSLP bit
(RCON<8>). Clearing the PMSLP bit enables the
Standby mode. When waking up from Standby mode,
the regulator needs to wait for TVREG to expire before
wake-up.
34.2.3
LOW-VOLTAGE/RETENTION
REGULATOR
When power-saving modes, such as Sleep and Deep
Sleep are used, PIC24FJ128GC010 family devices
may use a separate low-power, low-voltage/retention
regulator to power critical circuits. This regulator, which
operates at 1.2V nominal, maintains power to data
RAM and the RTCC while all other core digital logic is
powered down. It operates only in Sleep, Deep Sleep
and VBAT modes.
The low-voltage/retention regulator is described in more
detail in Section 10.1.3 “Low-Voltage/Retention
Regulator”.
 2012-2013 Microchip Technology Inc.
DS30009312B-page 409