PIC18F26K80-I Datasheet, PDF (549/622 Pages) Microchip Technology – 28/40/44/64-Pin, Enhanced Flash Microcontrollers with ECAN™ and nanoWatt XLP Technology

PIC18F66K80 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F66K80 Family (Industrial/Extended) (Continued)
PIC18F66K80 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Supply Current (IDD) Cont.^(2,3)
PIC18LFXXK80
PIC18FXXK80
PIC18FXXK80
2
5
mA -40°C to +125°C VDD = 3.3V⁽⁴⁾
Regulator Disabled
2
5
mA
-40°C to +125°C VDD = 3.3V⁽⁵⁾
Regulator Enabled
FOSC = 16 MHZ
(PRI_RUN mode, 4 MHz
EC oscillator with PLL)
2
6
mA -40°C to +125°C VDD = 5.5V⁽⁵⁾
Regulator Enabled
PIC18LFXXK80
PIC18FXXK80
PIC18FXXK80
7
11
mA -40°C to +125°C VDD = 3.3V⁽⁴⁾
Regulator Disabled
7
11
mA
-40°C to +125°C
VDD = 3.3V⁽⁵⁾
Regulator Enabled
FOSC = 64 MHz
(PRI_RUN mode, 16 MHz
EC oscillator with PLL)
8
12 mA -40°C to +125°C VDD = 5.5V⁽⁵⁾
Regulator Enabled
PIC18LFXXK80
PIC18FXXK80
PIC18FXXK80
7
11
mA -40°C to +125°C VDD = 3.3V⁽⁴⁾
Regulator Disabled
7
11
mA -40°C to +125°C VDD = 3.3V⁽⁴⁾
Regulator Enabled
FOSC = 64 MHz
(PRI_RUN mode,
EC oscillator)
8
12 mA -40°C to +125°C VDD = 5.5V⁽⁵⁾
Regulator Enabled
PIC18LFXXK80
PIC18FXXK80
PIC18FXXK80
2.3
5
mA -40°C to +125°C VDD = 3.3V⁽⁴⁾
Regulator Disabled
2.3
5
mA -40°C to +125°C VDD = 3.3V⁽⁵⁾
Regulator Enabled
FOSC = 64 MHz
(PRI_IDLE mode,
EC oscillator)
2.5
6
mA -40°C to +125°C VDD = 5.5V⁽⁵⁾
Regulator Enabled
Legend:
Note 1:
2:
3:
4:
5:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the
current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
For LF devices, RETEN (CONFIG1L<0>) = 1.
For F devices, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0.
 2010-2012 Microchip Technology Inc.
DS39977F-page 549