PIC18F26K80-I Datasheet, PDF (174/622 Pages) Microchip Technology – 28/40/44/64-Pin, Enhanced Flash Microcontrollers with ECAN™ and nanoWatt XLP Technology

PIC18F66K80 FAMILY
11.1.4 ANALOG AND DIGITAL PORTS
Many of the ports multiplex analog and digital function-
ality, providing a lot of flexibility for hardware designers.
PIC18F66K80 family devices can make any analog pin
analog or digital, depending on an application’s needs.
The ports’ analog/digital functionality is controlled by
the registers: ANCON0 and ANCON1.
Setting these registers makes the corresponding pins
analog and clearing the registers makes the ports digi-
tal. For details on these registers, see Section 23.0
“12-Bit Analog-to-Digital Converter (A/D) Module”
11.1.5 PORT SLEW RATE
The output slew rate of each port is programmable to
select either the standard transition rate, or a reduced
transition rate of ten percent of the standard transition
time, to minimize EMI. The reduced transition time is
the default slew rate for all ports.
REGISTER 11-4: SLRCON: SLEW RATE CONTROL REGISTER
U-0
—
bit 7
R/W-0
SLRG⁽¹⁾
R/W-0
SLRF⁽¹⁾
R/W-0
SLRE⁽²⁾
R/W-0
SLRD⁽²⁾
R/W-0
SLRC⁽²⁾
R/W-0
SLRB
R/W-0
SLRA
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
SLRG: PORTG Slew Rate Control bit⁽¹⁾
1 = All output pins on PORTG slew at 0.1 the standard rate
0 = All output pins on PORTG slew at standard rate
bit 5
SLRF: PORTF Slew Rate Control bit⁽¹⁾
1 = All output pins on PORTF slew at 0.1 the standard rate
0 = RAll output pins on PORTF slew at standard rate
bit 4
SLRE: PORTE Slew Rate Control bit⁽²⁾
1 = All output pins on PORTE slew at 0.1 the standard rate
0 = All output pins on PORTE slew at standard rate
bit 3
SLRD: PORTD Slew Rate Control bit⁽²⁾
1 = All output pins on PORTD slew at 0.1 the standard rate
0 = All output pins on PORTD slew at standard rate
bit 2
SLRC: PORTC Slew Rate Control bit⁽²⁾
1 = All output pins on PORTC slew at 0.1 the standard rate
0 = All output pins on PORTC slew at standard rate
bit 1
SLRB: PORTB Slew Rate Control bit
1 = All output pins on PORTB slew at 0.1 the standard rate
0 = All output pins on PORTB slew at standard rate
bit 0
SLRA: PORTA Slew Rate Control bit
1 = All output pins on PORTA slew at 0.1 the standard rate
0 = All output pins on PORTA slew at standard rate
Note 1: These bits are unimplemented and read back as ‘0’ on 28-pin and 40/44-pin devices.
2: These bits are unimplemented and read back as ‘0’ on 28-pin devices.
DS39977F-page 174
 2010-2012 Microchip Technology Inc.