DS925 Datasheet, PDF (6/109 Pages) Xilinx, Inc – DC and AC Switching Characteristics

Zynq UltraScale+ MPSoC Data Sheet: DC and AC Switching Characteristics
Table 2: Recommended Operating Conditions⁽¹⁾⁽²⁾ (Cont’d)
Symbol
Description
PL System Monitor
V_CCADC
V_REFP
PL System Monitor supply relative to GNDADC.
PL System Monitor externally supplied reference
voltage relative to GNDADC.
Temperature
Junction temperature operating range for extended (E)
temperature devices.⁽¹³⁾
T_j
Junction temperature operating range for industrial (I)
temperature devices.
Min
1.746
1.200
0
–40
Typ
1.800
1.250
–
–
Max
1.854
1.300
Units
V
V
100
°C
100
°C
Notes:
1. All voltages are relative to GND.
2. For the design of the power distribution system consult UltraScale Architecture PCB Design Guide (UG583).
3. V_{CC_PSINTFP_DDR} must be tied to V_{CC_PSINTFP}.
4. Includes V_{CCO_PSDDR} of 1.1V, 1.2V, 1.35V, 1.5V at ±5%.
5. Applies to all PS I/O supply banks.
6. If the battery-backed RAM or RTC is not used, connect V_{CC_PSBATT} to GND.
7. V_{CCINT_IO} must be connected to V_CCBRAM.
8.
Includes
5%.
V_CCO
of
1.0V
(HP
I/O
only),
1.2V,
1.35V,
1.5V,
1.8V,
2.5V
(HD
I/O
only)
at
±5%,
and
3.3V
(HD
I/O
only)
at
+3/–
9. V_{CCAUX_IO} must be connected to V_CCAUX.
10. The lower absolute voltage specification always applies.
11. A total of 200 mA per 52-pin bank should not be exceeded.
12. Each voltage listed requires filtering as described in UltraScale Architecture GTH Transceiver User Guide (UG576) or
UltraScale Architecture GTY Transceiver User Guide (UG578).
13. Devices labeled with the speed/temperature grade of -2LE can operate for a limited time at a junction temperature of
110°C. Timing parameters adhere to the same speed file at 110°C as they do below 110°C, regardless of operating voltage
(nominal voltage of 0.85V or a low-voltage of 0.72V). Operation at Tj = 110°C is limited to 1% of the device lifetime and
can occur sequentially or at regular intervals as long as the total time does not exceed 1% of the device lifetime.
Table 3: PS MIO Pull-up and Pull-down Current
Symbol
Description
I_RPU
I_RPD
Pad pull-up (when selected) at V_IN = 0V, V_{CCO_PSMIO} = 3.3V.
Pad pull-up (when selected) at V_IN = 0V, V_{CCO_PSMIO} = 2.5V.
Pad pull-up (when selected) at V_IN = 0V, V_{CCO_PSMIO} = 1.8V.
Pad pull-down (when selected) at V_IN = 3.3V.
Pad pull-down (when selected) at V_IN = 2.5V.
Pad pull-down (when selected) at V_IN = 1.8V.
Min
20
20
15
20
20
15
Max
80
80
65
80
80
65
Units
µA
µA
µA
µA
µA
µA
DS925 (v1.1) June 20, 2016
Advance Product Specification
www.xilinx.com
Send Feedback
6