PIC18F6390 Datasheet, PDF (65/412 Pages) Microchip Technology – 64/80-Pin Flash Microcontrollers with LCD Driver and nanoWatt Technology

PIC18F6390/6490/8390/8490
TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Applicable
Devices
Power-on Reset,
Brown-out Reset
MCLR Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
LCDDATA23
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA22
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA21
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA20
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA19
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA18
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA17
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA16
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA15
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA14
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA13
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA12
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA11
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
SPBRG2
6X90 8X90
0000 0000
0000 0000
uuuu uuuu
RCREG2
6X90 8X90
0000 0000
0000 0000
uuuu uuuu
TXREG2
6X90 8X90
0000 0000
0000 0000
uuuu uuuu
TXSTA2
6X90 8X90
0000 0010
0000 0010
uuuu uuuu
RCSTA2
6X90 8X90
0000 000x
0000 000x
uuuu uuuu
LCDDATA10
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA9
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA8
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA7
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA6
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA5
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA4
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA3
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA2
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA1
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
LCDDATA0
6X90 8X90
xxxx xxxx
uuuu uuuu
uuuu uuuu
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
4: See Table 4-3 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read ‘0’.
 2004 Microchip Technology Inc.
Preliminary
DS39629B-page 63