82845PE Datasheet, PDF (71/176 Pages) Intel Corporation – 82845GE Graphics and Memory Controller Hub (GMCH) and 82845PE Memory Controller Hub (MCH)

Register Description
3.5.1.32
GMCHCFG—GMCH/MCH Configuration Register (Device 0)
Address Offset:
Default Value:
Access:
Size:
C6–C7h
0C01h
R/W, RO
16 bits
Bit
15:13
12
11:10
Description
Intel Reserved.
Core/PSB Frequency Select (PSBFREQ)—RO. The default value of this bit is set by the strap
assigned to pin PSB_SEL and is latched at the rising edge of PWROK.
0 = PSB frequency is 400 MHz (PSB_SEL sampled low on PWROK assertion)
1 = PSB frequency is 533 MHz (PSB_SEL sampled high on PWROK assertion)
System Memory Frequency Select (SMFREQ)—R/W¹.
00 = Intel Reserved
01 = System Memory frequency is set to 166 MHz (DDR333)
10 = System Memory frequency is set to 133 MHz (DDR266)
11 = Reserved (Default)
NOTE:
1. When writing a new value to this bit, a warm reset through the Intel^® ICH4 must be executed
before the bit becomes effective. This must be enforced by BIOS/SW. However, changing this bit
in SW requires a “warm reset.”
9:6 Intel Reserved.
MDA Present (MDAP). This bit works with the VGA enable bits in the BCTRL1 register of Device 1
to control the routing of processor initiated transactions targeting MDA compatible I/O and memory
address ranges. This bit should not be set if Device 1's VGA enable bit is not set. If Device 1's VGA
enable bit is set, then accesses to I/O address range x3BCh–x3BFh are forwarded to the hub
interface. If the VGA enable bit is not set then accesses to I/O address range x3BCh–x3BFh are
treated just like any other I/O accesses. That is, the cycles are forwarded to AGP if the address is
within the corresponding IOBASE and IOLIMIT and ISA enable bit is not set; otherwise, they are
5 ^{forwarded to the hub interface. MDA resources are:}
Memory: 0B0000h–0B7FFFh
I/O:
3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh
(including ISA address aliases, A[15:10] are not used in decode)
Any I/O reference that includes the I/O locations listed above, or their aliases, will be forwarded to
hub interface even if the reference includes I/O locations not listed above.
Refer to the Chapter 4 for further information.
4 Intel Reserved.
82845PE: Reserved.
82845GE: AGP Mode (AGP/DVO#)—RO. This bit is Read Only and reflects the ADD_DETECT
strap value. This strap bit determines the function of the AGP I/O signal.
3
0 = 2xDVO
RO ^{1 = AGP}
When the strap is sampled low, this bit will be a 0 and DVO mode will be selected. When the strap is
sampled high, this bit will be a 1 and AGP mode will be selected.
Note that when this bit is set to 0 (DVO mode), Device 1 is disabled (configuration cycles fall-through
to HI) and the Next Pointer field in CAPREG will be hardwired to zeros.
PSB IOQ Depth (IOQD)—RO. This bit is RO and reflects the HA7# strap value. It indicates the depth
of the PSB IOQ.
0 = 1 deep
2
1 = 12 on the bus, 8 on the (G)MCH
When the strap is sampled low, this bit will be a 0 and the PSB IOQ depth is set to 1. When the strap
is sampled high, this bit will be a 1 and the PSB IOQ depth is set to the maximum (12 on the bus, 8
on the (G)MCH).
1:0 Intel Reserved.
Intel^® 82845GE/82845PE Datasheet
71