TA1360ANG Datasheet, PDF (85/108 Pages) Toshiba Semiconductor – TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic

TA1360ANG
Note
No.
Characteristics
SW3
T18 IK input
A
amplitude
or
C
T19 IK input cover C
range
T20 Analog RGB
A
gain
T21 Analog RGB
A
white peak
slice level
SW4
B
B
B
B
SW5
B
B
B
B
Test Conditions
SW Mode
SW33 SW34 SW35
A
A
A
SW37
A
SW38
A
SW39
A 1.
2.
Test Method
Input signal 1(f₀ = 100 kHz, picture period amplitude = 0.2 Vp-p) from pin 3. Control drive
gain adjustment data so that pins 41 and 42 picture period amplitude equals that of pin 43.
Set subaddress (02) data to (40).
3. Measure voltage amplitude of pin-45 input signal in ACB insertion period.
1H = IK_R 2H = IK_G 3H = IK_B
A
A
A
A
A
A 1. Input signal 1(f₀ = 100 kHz, picture period amplitude = 0.2 Vp-p) from pin 3. Control drive
gain adjustment data so that pins 41 and 42 picture period amplitude equals that of pin 43.
2. Set subaddress (02) data to (40).
3. Measure pin 45 DC voltage in VŋBLK period. (#45VBLK)
4. Apply the current externally to pin 45.
5. Measure DC voltage of pin 45 in VŋBLK period when pin-43 picture period voltage begins to
be decreased. (#45VBLK+)
6. Apply current outward from pin 45.
7. Measure DC voltage of pin 45 in VŋBLK period when pin-43 picture period voltage begins to
be increased. (#45VBLK−)
8. DIK_in+ = (#45VBLK+) − (#45VBLK)
DIK_in− = (#45VBLK−) + (#45VBLK)
A
A
A
A
A
A 1. Input signal 1(f₀ = 100 kHz, picture period amplitude = 0.2 Vp-p) from pin 3. Control drive
or
or
or
gain adjustment data so that pins 41 and 42 picture period amplitude equals that of pin 43.
B
B
B
2. Apply 5-V external voltage to pin 49.
3. Input signal 1(f₀ = 100 kHz, picture period amplitude = 0.2 Vp-p) from pin 35.
4. Measure pin 43 picture period amplitude, v43R.
5. Repeat the steps 3 and 4 above with the following pins:
Input from pin 34, and measure output from pin 42 (v42G).
Input from pin 33, and measure output from pin 41 (v41B).
6 Calculate the following equations. GTXR = v43R/0.2 GTXG = v42G/0.2 GTXB = v41B/0.2
A
A
A
A
A
A 1. Input signal 1(f₀ = 100 kHz, picture period amplitude = 0.2 Vp-p) from pin 3. Control drive
gain adjustment data so that pins 41 and 42 picture period amplitude equals that of pin 43.
2. Apply 5-V external voltage to pin 49.
3. Set RGB contrast data to maximum (7F).
4. Input signal 2 to pin 35. Gradually increase picture amplitude, and measure picture period
amplitude voltage when output from pin 43 is clipped.
5. Repeat the steps 3 and 4 above with following pins: Input from pin 34 and measure output
from pin 42. Input from pin 33 and measure output pin 41.
85
2003-01-21