PIC18F87J90 Datasheet, PDF (343/450 Pages) Microchip Technology – 64/80-Pin, High-Performance Microcontrollers with LCD Driver and nanoWatt Technology

PIC18F87J90 FAMILY
TABLE 26-2: PIC18F87J90 FAMILY INSTRUCTION SET (CONTINUED)
Mnemonic,
Operands
Description
16-Bit Instruction Word
Cycles
MSb
LSb
Status
Affected
Notes
BIT-ORIENTED OPERATIONS
BCF
f, b, a Bit Clear f
1
1001 bbba ffff ffff None
1, 2
BSF
f, b, a Bit Set f
1
1000 bbba ffff ffff None
1, 2
BTFSC f, b, a Bit Test f, Skip if Clear
1 (2 or 3) 1011 bbba ffff ffff None
3, 4
BTFSS f, b, a Bit Test f, Skip if Set
1 (2 or 3) 1010 bbba ffff ffff None
3, 4
BTG
f, b, a Bit Toggle f
1
0111 bbba ffff ffff None
1, 2
CONTROL OPERATIONS
BC
n
Branch if Carry
1 (2)
1110 0010 nnnn nnnn None
BN
n
Branch if Negative
1 (2)
1110 0110 nnnn nnnn None
BNC
n
Branch if Not Carry
1 (2)
1110 0011 nnnn nnnn None
BNN
n
Branch if Not Negative
1 (2)
1110 0111 nnnn nnnn None
BNOV
n
Branch if Not Overflow
1 (2)
1110 0101 nnnn nnnn None
BNZ
n
Branch if Not Zero
1 (2)
1110 0001 nnnn nnnn None
BOV
n
Branch if Overflow
1 (2)
1110 0100 nnnn nnnn None
BRA
n
Branch Unconditionally
2
1101 0nnn nnnn nnnn None
BZ
n
Branch if Zero
1 (2)
1110 0000 nnnn nnnn None
CALL
n, s Call Subroutine 1st word
2
1110 110s kkkk kkkk None
2nd word
1111 kkkk kkkk kkkk
CLRWDT — Clear Watchdog Timer
1
0000 0000 0000 0100 TO, PD
DAW
— Decimal Adjust WREG
1
0000 0000 0000 0111 C
GOTO
n
Go to Address 1st word
2
1110 1111 kkkk kkkk None
2nd word
1111 kkkk kkkk kkkk
NOP
— No Operation
1
0000 0000 0000 0000 None
NOP
— No Operation
1
1111 xxxx xxxx xxxx None
4
POP
— Pop Top of Return Stack (TOS) 1
0000 0000 0000 0110 None
PUSH
— Push Top of Return Stack (TOS) 1
0000 0000 0000 0101 None
RCALL n
Relative Call
2
1101 1nnn nnnn nnnn None
RESET
Software Device Reset
1
0000 0000 1111 1111 All
RETFIE s
Return from Interrupt Enable 2
0000 0000 0001 000s GIE/GIEH,
PEIE/GIEL
RETLW k
Return with Literal in WREG 2
0000 1100 kkkk kkkk None
RETURN s
Return from Subroutine
2
0000 0000 0001 001s None
SLEEP — Go into Standby mode
1
0000 0000 0000 0011 TO, PD
Note 1: When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be
that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and
is driven low by an external device, the data will be written back with a ‘0’.
2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
if assigned.
3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The
second cycle is executed as a NOP.
4: Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all
program memory locations have a valid instruction.
 2010 Microchip Technology Inc.
DS39933D-page 343