SMJ320C6414 Datasheet, PDF (106/133 Pages) Texas Instruments – FIXED-POINT DIGITAL SIGNAL PROCESSORS

SMJ320C6414, SMJ320C6415, SMJ320C6416
FIXEDĆPOINT DIGITAL SIGNAL PROCESSORS
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
RESET TIMING (CONTINUED)
CLKOUT4
CLKOUT6
1
RESET
2
3
ECLKIN
4
5
ECLKOUT1
ECLKOUT2
6
7
EMIF Z Group‡§
8
9
EMIF High Group‡
10
11
EMIF Low Group‡
12
13
Low Group‡
14
15
Z Group‡§
Boot and Device
Configuration Inputs§¶
17
16
† _{These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a}
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., ECLKIN, ECLKOUT1,
and ECLKOUT2].
‡ _{EMIF Z group consists of:}
AEA[22:3], BEA[20:1], AED[63:0], BED[15:0], CE[3:0], ABE[7:0], BBE[1:0], ARE/SDCAS/SADS/SRE,
AWE/SDWE/SWE, and AOE/SDRAS/SOE, SOE3, ASDCKE, and PDT.
EMIF high group consists of: AHOLDA and BHOLDA (when the corresponding HOLD input is high)
EMIF low group consists of: ABUSREQ and BBUSREQ; AHOLDA and BHOLDA (when the corresponding HOLD input is low)
Low group consists of:
XSP_CS, CLKX2/XSP_CLK, and DX2/XSP_DO; all of which apply only when PCI EEPROM (BEA13)
is enabled (with PCI_EN = 1 and MCBSP2_EN = 0). Otherwise, the CLKX2/XSP_CLK and DX2/XSP_DO
pins are in the Z group. For more details on the PCI configuration pins, see the Device Configurations section
of this data sheet.
Z group consists of:
HD[31:0]/AD[31:0], CLKX0, CLKX1/URADDR4, CLKX2/XSP_CLK, FSX0, FSX1/UXADDR3, FSX2, DX0,
DX1/UXADDR4, DX2/XSP_DO, CLKR0, CLKR1/URADDR2, CLKR2, FSR0, FSR1/UXADDR2, FSR2,
TOUT0, TOUT1, TOUT2, GP[8:0], GP10/PCBE3, HR/W/PCBE2, HDS2/PCBE1, PCBE0, GP13/PINTA,
GP11/PREQ, HDS1/PSERR, HCS/PPERR, HCNTL1/PDEVSEL, HAS/PPAR, HCNTL0/PSTOP,
HHWIL/PTRDY (16-bit HPI mode only), HRDY/PIRDY, HINT/PFRAME, UXDATA[7:0], UXSOC, UXCLAV,
and URCLAV.
§ _{If BEA[20:13, 11, 7] and HD5/AD5 pins are actively driven, care must be taken to ensure no timing contention between parameters 6, 7, 14, 15,}
16, and 17.
¶ _{Boot and Device Configurations Inputs (during reset) include: EMIFB address pins BEA[20:13, 11, 7] and HD5/AD5.}
The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
Figure 37. Reset Timing^†
106
• POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443