TC290 Datasheet, PDF (473/476 Pages) Infineon Technologies AG – 32-Bit Single-Chip Micocontroller

TC290 / TC297 / TC298 / TC299 BB-Step
HistoryChanges from version version 0.71 to 1.1
– Change note of T_A from 'valid for all SAL products with package' to 'valid for all SAL products'
4.3
Changes from version version 0.71 to 1.1
• Package Chapter
– update information for VADC functions ‘with pull down diagnostics’ and ‘MD’, no change in pinning
– correct for P22.2 PU1 to PU
• DSADC
– Change note of SNR from 'f_PB = 30 kHz; V_DDM = ±5%' to 'f_PB = 30 kHz; V_DDM = ±5%; f_MOD = 20 MHz; GAIN = 1'
– Add footnote 'The defined limits are only valid if the following condition is not applicable: T_J > 150°C and
V_VAREF > V_DDM.' to SNR
– Change note of I_OZ6 from '-2 µA' to '-3 µA'
– Change note of SNR from 'f_PB = 100 kHz; V_DDM = ±10%' to 'f_PB = 100 kHz; V_DDM = ±10%; f_MOD = 20 MHz;
GAIN = 1'
– Remove footnote 'Systematic offset shift' from ED_OFF
– Add footnote 'The total DC error for the uncalibrated case can be calculated by the geometric addition of
ED_GAIN and ED_OFF' to ED_OFF
– Change note of ED_GAIN from 'calibrated' to 'calibrated; GAIN = 1; MODCFG.INCFGx=01'
• DSADC_33V
– Change note of SNR from 'f_PB = 30kHz; V_DDM = ±5%' to 'f_PB = 30kHz; V_DDM = ±5%; f_MOD = 20 MHz; GAIN = 1'
– Change min value of ED_GAIN from -0.2 % to -0.3 %
– Change note of ED_GAIN from '0.2 %' to '0.3 %'
– Change min value of I_OZ6 from -2 µA to -3 µA
– Change note of SNR from 'f_PB = 100kHz; V_DDM = ±10%' to 'f_PB = 100kHz; V_DDM = ±10%; f_MOD = 20 MHz;
GAIN = 1'
– Remove footnote 'Systematic offset shift' from ED_OFF
– Add footnote 'The total DC error for the uncalibrated case can be calculated by the geometric addition of
ED_GAIN and ED_OFF' to ED_GAIN (
– Change note of ED_GAIN from 'calibrated' to 'calibrated; GAIN = 1; MODCFG.INCFGx=01'
– Change min value of ED_OFF from -350 mV to -100 mV
– Change typ value of ED_OFF from -150 mV to 0 mV
– Change maxvalue of ED_OFF from 0 mV to 100 mV
• Changes in table 'Overload Parameters' of Overload
– Remove I_INSA
– Change note of I_INANA from '-1 mA' to '-3 mA'
– Change note of K_OVAN from ''-5mA < I_IN < -1mA'' to ''Analog Inputs overlaid with class LP pads or pull down
diagnostics; -5mA < I_IN < -1mA''
– Change note of K_OVAN from '3*10^-3' to '1*10^-2'
– Change note of K_OVAN from 'else; -1mA < I_IN < 0mA' to 'else; -5mA < I_IN < 0mA'
• Reset Timings
– Change max value of t_BP from 1.1 ms to 1.11 ms
Data Sheet
4-467
V 1.1 2015-05
TC290/TC297/TC298/TC299 BB-Step Data Sheet downloaded by saravanakumar maniyam (larsen and Toubro limited) at 08 Sep 2015 08:06