TC290 Datasheet, PDF (467/476 Pages) Infineon Technologies AG – 32-Bit Single-Chip Micocontroller

TC290 / TC297 / TC298 / TC299 BB-Step
HistoryChanges from version version 0.6 to 0.71
– Change note of I_OZ3 from '' to 'V_AGNDx = V_AGND2'
– Add max 2.5 µA to I_OZ3
– Change note of I_OZ3 from '' to 'V_AGNDx = V_AGND2'
– Change note of Q_CONV from 'V_AIN = 5V, charge consumed from reference pin, precharging enabled' to 'V_AIN
= 5 V, charge consumed from reference pin, precharging enabled'
– Change note of Q_CONV from 'V_AIN = 5V, charge consumed from reference pin, precharging disabled' to 'V_AIN
= 5 V, charge consumed from reference pin, precharging disabled'
– Change max value of EN_RMS from 0.5 LSB to 0.75 LSB
– Change note of R_AIN from 'valid for analoge inputs mapped to GPIOs' to 'valid for analog inputs mapped to
GPIOs'
– Add min -4 µA to I_OZ2
– Add V_AREF=V_DDM V to V_AREF
– Add min -7 µA to I_OZ2
– Add V_AREF=V_DDM V to V_AREF
– Add max 7 µA to I_OZ2
– Add max 4 µA to I_OZ2
– Add min -7 µA to I_OZ3
– Add min -13 µA to I_OZ3
– Add max 7 µA to I_OZ3
– Add max 13 µA to I_OZ3
– Add typ 0.5 LSB to EN_RMS
• Changes in table 'Master Mode Timing, LVDSM output pads for data and clock' of QSPI/3.3V
– Change min value of t₅₂ from 37 ns to 20 ns
• DSADC_33V
– Change max value of ED_GAIN from 0.1 % to 0.2 %
– Change min value of ED_GAIN from -0.1 % to -0.2 %
– Change note of SNR from 'f_PB = 30kHz' to 'f_PB = 30kHz; V_DDM = ±5%'
– Change note of SNR from 'f_PB = 50kHz' to 'f_PB = 50kHz; V_DDM = ±5%'
– Change note of SNR from 'f_PB = 100kHz' to 'f_PB = 100kHz; V_DDM = ±5%'
– Change note of SNR from 'f_PB = 30kHz' to 'f_PB = 30kHz; V_DDM = ±5%'
– Change note of SBA from '1,5 ... 2 f_D' to '1.5 ... 2 f_D'
– Change note of SBA from '0,5 ... 1 f_D' to '0.5 ... 1 f_D'
– Change note of SNR from 'f_PB = 100kHz' to 'f_PB = 100kHz; V_DDM = ±5%'
– Change note of SNR from 'f_PB = 50kHz' to 'f_PB = 50kHz; V_DDM = ±5%'
– Change note of SBA from '2,5 ... OSR/2 f_D' to '2.5 ... OSR/2 f_D'
– Change note of SFDR from 'VCM = 2.2V, DC coupled' to 'V_CM = 2.2 V, DC coupled; V_DDM = ±5%'
• Changes in table 'Receive Parameters' of ERAY
– Change description of t_{dCCTxAsymAccept15} from 'Acceptance of asymmetriy at receiving part' to 'Acceptance of
asymmetry at receiving part'
– Change description of t_{dCCTxAsymAccept25} from 'Acceptance of asymmetriy at receiving part' to 'Acceptance of
asymmetry at receiving part'
– Change description of t_{dCCTxAsymAccept15} from 'Acceptance of asymmetriy at receiving part' to 'Acceptance of
asymmetry at receiving part'
Data Sheet
4-461
V 1.1 2015-05
TC290/TC297/TC298/TC299 BB-Step Data Sheet downloaded by saravanakumar maniyam (larsen and Toubro limited) at 08 Sep 2015 08:06