TC290 Datasheet, PDF (413/476 Pages) Infineon Technologies AG – 32-Bit Single-Chip Micocontroller

TC290 / TC297 / TC298 / TC299 BB-Step
Electrical SpecificationQSPI Timings, Master and Slave Mode
Table 3-72 Master Mode timing MPRm/MP+m/MPm/LPm output pads (cont’d)
Parameter
Symbol
Values
Unit Note / Test Condition
Min.
Typ.
Max.
MTSR delay from SCLKO
t₅₁ CC
-25
-
shifting edge
33
ns
C_L=50pF
SLSOn deviation from the ideal t₅₁₀ CC
programmed position
MRST setup to SCLK latching t₅₂ SR
edge ⁴⁾
-35
-
120 ⁴⁾⁵⁾ -
35
ns
C_L=50pF
-
ns
C_L=50pF
MRST hold from SCLK latching t₅₃ SR
-13 ⁴⁾⁵⁾
-
-
ns
C_L=50pF
edge
1) Documented value is valid for master transmit or slave receive only. For full duplex the external SPI counterpart timing has
to be taken into account.
2) The PLL jitter is not included. It should be considered additionally, corresponding to the used baudrate. The duty cycle can
be adjusted using the bit fields ECONz.A, B and C with the finest granularity of T_MAX = 1 / f_MAX.
3) Positive deviation lenghtens the high time and shortens the low time of a clock period. Negative deviation does the
opposite.
4) For compensation of the average on-chip delay the QSPI module provides the bit fields ECONz.A, B and C.
5) The setup and hold times are valid for both settings of the input pads thresholds: TTL and AL.
Table 3-73 Master Mode Weak output pads
Parameter
Symbol
Values
Unit Note / Test Condition
SCLKO clock period ¹⁾
Deviation from the ideal duty
cycle ^{2) 3)}
t₅₀ CC
t₅₀₀ CC
Min.
2000
-110
Typ.
-
-
Max.
-
125
ns
C_L=50pF
ns
0 < C_L < 200pF
MTSR delay from SCLKO
t₅₁ CC
-170
-
shifting edge
170
ns
C_L=50pF
SLSOn deviation from the ideal t₅₁₀ CC
-170
-
programmed position
170
ns
C_L=50pF
MRST setup to SCLK latching t₅₂ SR
510 ⁴⁾⁵⁾ -
-
ns
C_L=50pF
edge ⁴⁾
MRST hold from SCLK latching t₅₃ SR
-40 ⁴⁾⁵⁾
-
-
ns
C_L=50pF
edge
1) Documented value is valid for master transmit or slave receive only. For full duplex the external SPI counterpart timing has
to be taken into account.
2) The PLL jitter is not included. It should be considered additionally, corresponding to the used baudrate. The duty cycle can
be adjusted using the bit fields ECONz.A, B and C with the finest granularity of T_MAX = 1 / f_MAX.
3) Positive deviation lenghtens the high time and shortens the low time of a clock period. Negative deviation does the
opposite.
4) For compensation of the average on-chip delay the QSPI module provides the bit fields ECONz.A, B and C.
5) The setup and hold times are valid for both settings of the input pads thresholds: TTL and AL.
Data Sheet
3-407
V 1.1 2015-05
TC290/TC297/TC298/TC299 BB-Step Data Sheet downloaded by saravanakumar maniyam (larsen and Toubro limited) at 08 Sep 2015 08:06