COP8AME9_14 Datasheet, PDF (6/102 Pages) Texas Instruments – COP8AME9 8-Bit CMOS Flash Microcontroller with 8k Memory, Dual Op Amps, Virtual EEPROM, Temperature Sensor, 10-Bit A/D and Brownout Reset

COP8AME9, COP8ANE9
SNOS930F – MARCH 2001 – REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings ⁽¹⁾⁽²⁾
Supply Voltage (V_CC)
Voltage at Any Pin
Total Current into V_CC Pin (Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
ESD Protection Level
7V
−0.3V to V_CC +0.3V
200 mA
200 mA
−65°C to +140°C
2 kV (Human Body Model)
(1) Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not
ensured when operating the device at absolute maximum ratings.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Electrical Characteristics DC Electrical Characteristics (−40°C ≤ T_A ≤ +85°C)
Datasheet min/max specification limits are ensured by design, test, or statistical analysis.
Parameter
Conditions
Min
Typ
Operating Voltage
4.5
Power Supply Rise Time
Power Supply Ripple ⁽¹⁾
Supply Current on V_CC pin⁽²⁾
High Speed Mode
10
Peak-to-Peak
CKI = 10 MHz
CKI = 3.33 MHz
Dual Clock Mode
V_CC = 5.5V, t_C = 0.5 μs
V_CC = 4.5V, t_C = 1.5 μs
CKI = 10 MHz, Low Speed OSC = 32 kHz
CKI = 3.33 MHz, Low Speed OSC = 32 kHz
Low Speed Mode
V_CC = 5.5V, t_C = 0.5 μs
V_CC = 4.5V, t_C = 1.5 μs
Low Speed OSC = 32 kHz
V_CC = 5.5V
60
HALT Current with BOR Disabled (Test Mode only)⁽³⁾
High Speed Mode
Dual Clock Mode
V_CC = 5.5V, CKI = 0 MHz
<1
V_CC = 5.5V, CKI = 0 MHz,
Low Speed OSC = 32 kHz
<5
Low Speed Mode
Idle Current on V_CC pin ⁽²⁾
High Speed Mode
V_CC = 5.5V, CKI = 0 MHz,
Low Speed OSC = 32 kHz
<5
CKI = 10 MHz
CKI = 3.33 MHz
Dual Clock Mode
V_CC = 5.5V, t_C = 0.5 μs
V_CC = 4.5V, t_C = 1.5 μs
CKI = 10 MHz, Low Speed OSC = 32 kHz
CKI = 3.33 MHz, Low Speed OSC = 32 kHz
Low Speed Mode
V_CC = 5.5V, t_C = 0.5 μs
V_CC = 4.5V, t_C = 1.5 μs
Low Speed OSC = 32 kHz
V_CC = 5.5V
15
Supply Current for BOR Feature
V_CC = 5.5V
Max
5.5
50 x 10⁶
0.1 V_CC
Units
V
ns
V
14.5
mA
7
mA
14.5
mA
7
mA
103
μA
10
μA
17
μA
17
μA
2.5
mA
1.2
mA
2.5
mA
1.2
mA
30
μA
45
μA
(1) Maximum rate of voltage change must be < 0.5 V/ms.
(2) Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180° out of phase with CKI, inputs
connected to V_CC and outputs driven low but not connected to a load.
(3) The HALT mode will stop CKI from oscillating. Measurement of I_DD HALT is done with device neither sourcing nor sinking current; with
L, B, G0, and G2–G5 programmed as low outputs and not driving a load; all inputs tied to V_CC; A/D converter and clock monitor and
BOR disabled. Parameter refers to HALT mode entered via setting bit 7 of the G Port data register.
6
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: COP8AME9 COP8ANE9