PIC16F193X Datasheet, PDF (95/418 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt Technology

PIC16F193X/LF193X
6.4 PORTC and TRISC Registers
PORTC is a 8-bit wide, bidirectional port. The
corresponding data direction register is TRISC
(Register 6-13). Setting a TRISC bit (= 1) will make the
corresponding PORTC pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISC bit (= 0) will make the corresponding
PORTC pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 6-3 shows how to initialize PORTC.
Reading the PORTC register (Register 6-11) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch.
The TRISC register (Register 6-13) controls the PORTC
pin output drivers, even when they are being used as
analog inputs. The user should ensure the bits in the
TRISC register are maintained set when using them as
analog inputs. I/O pins configured as analog input always
read ‘0’.
EXAMPLE 6-3: INITIALIZING PORTC
BANKSEL PORTC
CLRF PORTC
BANKSEL TRISC
MOVLW B‘00001100’
MOVWF TRISC
;
;Init PORTC
;
;Set RC<3:2> as inputs
;and set RC<7:4,1:0>
;as outputs
The location of the CCP2 function is controlled by the
CCP2SEL bit in the APFCON register (refer to
Register 6-1).
REGISTER 6-11: PORTC: PORTC REGISTER
R/W-x/u
RC7
bit 7
R/W-x/u
RC6
R/W-x/u
RC5
R/W-x/u
RC4
R/W-x/u
RC3
R/W-x/u
RC2
R/W-x/u
RC1
R/W-x/u
RC0
bit 0
Legend:
R = Readable bit
u = bit is unchanged
‘1’ = Bit is set
W = Writable bit
x = Bit is unknown
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
bit 7-0
RC<7:0>: PORTC General Purpose I/O Pin bits
1 = Port pin is > VIH
0 = Port pin is < VIL
REGISTER 6-12: LATC: PORTC DATA LATCH REGISTER
R/W-x/u
LATC7
bit 7
R/W-x/u
LATC6
R/W-x/u
LATC5
R/W-x/u
LATC4
R/W-x/u
LATC3
R/W-x/u
LATC2
R/W-x/u
LATC1
R/W-x/u
LATC0
bit 0
Legend:
R = Readable bit
u = bit is unchanged
‘1’ = Bit is set
W = Writable bit
x = Bit is unknown
‘0’ = Bit is cleared
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
bit 7-0
LATC<7:0>: PORTC Output Latch Value bits⁽¹⁾
Note 1: Writes to PORTC are actually written to corresponding LATC register. Reads from PORTC register is
return of actual I/O pin values.
© 2008 Microchip Technology Inc.
Preliminary
DS41364A-page 93