PIC16F193X Datasheet, PDF (366/418 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt Technology

PIC16F193X/LF193X
28.3 DC Characteristics: PIC16F193X/LF193X-I/E (Power-Down) (Continued)
PIC16LF193X
PIC16F193X
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
D027
D027
D027A
D027A
D028
D028
D029
D029
Device Characteristics Min.
Power-down Base Current (IPD)⁽²⁾
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Typ†
0.1
0.1
3.5
4
4.5
250
250
280
280
280
3.5
7
3.5
7
32
1
10
100
1
10
100
Max.
+85°C
Max.
+125°C
Units
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
TBD TBD μA
Conditions
VDD
Note
1.8 A/D Current (Note 1, Note 4), no
3.0 ^{conversion in progress}
1.8 A/D Current (Note 1, Note 4), no
3.0 ^{conversion in progress}
5.0
1.8 A/D Current (Note 1, Note 4),
3.0 ^{conversion in progress}
1.8 A/D Current (Note 1, Note 4,
3.0 ^{Note 5), conversion in progress}
5.0
1.8 Cap Sense
3.0
1.8 Cap Sense
3.0
5.0
3.6 LCD Bias Ladder, Low-power
3.6 LCD Bias Ladder, Medium-power
3.6 LCD Bias Ladder, High-power
5.0 LCD Bias Ladder, Low-power
5.0 LCD Bias Ladder, Medium-power
5.0 LCD Bias Ladder, High-power
*
†
Legend:
Note 1:
2:
3:
4:
5:
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
TBD = To Be Determined
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
Fixed Voltage Reference is automatically enabled whenever the BOR is enabled.
A/D oscillator source is FRC.
0.1 μF capacitor on VCAP (RA0).
DS41364A-page 364
Preliminary
© 2008 Microchip Technology Inc.