TI380C27 Datasheet, PDF (27/77 Pages) Texas Instruments – DUAL-PROTOCOL COMMPROCESSOR

TI380C27
DUAL-PROTOCOL COMMPROCESSOR
SPWS014A – APRIL 1994 – REVISED MARCH 1995
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)^†
Supply voltage, V_DD (see Note 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage range (see Note 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 20 V
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 2 V to 7 V
Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9 W
Operating free-air temperature range, T_A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 8: Voltage values are with respect to VSS.
recommended operating conditions
MIN NOM MAX
UNIT
VDD Supply voltage
4.75
5 5.25
V
VSS Supply voltage (see Note 9)
0
0
0
V
TTL-level signal
2
VDD + 0.3
VIH High-level input voltage
OSCIN
2.4
VDD + 0.3
V
RCLK, PXTALIN, RCVR
2.6
VDD + 0.3
VIL Low-level input voltage, TTL-level signal (see Note 10)
– 0.3
0.8
V
IOH High-level output current
– 400
µA
IOL Low-level output current (see Note 11)
2
mA
TA
Operating free-air temperature
0
70
°C
TC Operating case temperature
100
°C
NOTES: 9. All VSS pins should be routed to minimize inductance to system ground.
10. The algebraic convention, where the more negative (less positive) limit is designated as a minimum, is used for logic-voltage levels
only.
11. Output current of 2 mA is sufficient to drive five low-power Schottky TTL loads or ten advanced low-power Schottky TTL loads (worst
case).
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS^‡
MIN TYP MAX UNIT
VOH High-level output voltage, TTL-level signal (see Note 12) VDD = MIN, IOH = MAX
2.4
V
VOL Low-level output voltage, TTL-level signal
VDD = MIN, IOL = MAX
0.6 V
IO
High-impedance output current
VDD = MAX,
VDD = MAX,
VO = 2.4 V
VO = 0.4 V
20
µA
– 20
II
Input current, any input or input / output
VI = VSS to VDD
± 20 µA
IDD Supply current
VDD = MAX
160 mA
ISCM Supply current, slow-clock mode
VDD = 5 V
3
mA
Ci
Input capacitance, any input
f = 1 MHz,
Others at 0 V
15 pF
Co
Output capacitance, any output or input / output
f = 1 MHz,
Others at 0 V
15 pF
‡ _{For conditions shown as MIN or MAX, use the appropriate value specified under the recommended operating conditions.}
NOTE 12: The following signals require an external pullup resistor: SRAS/SAS, SRDY/SDTACK, SRD/SUDS, SWR/SLDS, EXTINT0 – EXTINT3,
and MBRQ.
• POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
27