M16C26 Datasheet, PDF (185/239 Pages) Renesas Technology Corp – 16-BIT CMOS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/20 SERIES

Udenvdeelropment
Preliminary Specifications Rev.
Specifications in this manual are
Electrical Characteristics (Vcc = 3V)
0.9
tentative
and
subject to change.
SINGLE-CHIP 16-BIT
M16C/26 Group
CMOS MICROCOMPUTER
VCC = 3V
Table 1.18.24. Electrical characteristics (referenced to VCC = 2.7 to 3.3V, VSS = 0V
at Topr = – 20^oC to 85^oC / – 40^oC to 85^oC (Note 1), f(XIN) = 10MHZ with wait
unless otherwise specified)
Symbol
Parameter
HIGH output P15 to P17, P60 to P67, P72 to P77, P80 to P83,
VOH
voltage
P85 to P87, P90 to P93, P100 to P107
Measuring condition
IOH=-1mA
Standard
Min. Typ. Max. ^Unit
2.5
V
VOH
HIGH output _XOUT
voltage
HIGHPOWER
LOWPOWER
HIGH output XCOUT
voltage
HIGHPOWER
LOWPOWER
LOW output P15 to P17, P60 to P67, P70 to P77, P80 to P83,
VOL
voltage
P85 to P87, P90 to P93, P100 to P107
IOH=-0.1mA
IOH=-50µA
With no load applied
With no load applied
IOL=1mA
2.5
2.5
V
2.5
V
1.6
0.5
V
VOL
VT+-VT-
LOW output
voltage
LOW output
voltage
Hysteresis
XOUT
HIGHPOWER
LOWPOWER
XCOUT
HIGHPOWER
LOWPOWER
TA0IN to TA4IN, TB0IN to TB2IN,
INT0, INT1, INT3 to INT5, NMI,
ADTRG, CTS0 to CTS2, SCL, SDA,
CLK0 to CLK2, TA2OUT to TA4OUT,
KI0 to KI3, RxD0 to RxD2
VT+-VT-
IIH
IIL
RPULLUP
Hysteresis
HIGH input
current
LOW input
current
Pull-up
resistance
RESET
P15 to P17, P60 to P67, P70 to P77, P80 to P83,
P85 to P87, P90 to P93, P100 to P107
XIN, RESET, CNVss
P15 to P17, P60 to P67, P70 to P77, P80 to P83,
P85 to P87, P90 to P93, P100 to P107
XIN, RESET, CNVss
P15 to P17, P60 to P67, P72 to P77, P80 to P83,
P85 to P87, P90 to P93, P100 to P107
IOL=0.1mA
IOL=50µA
With no load applied
With no load applied
VI=3V
VI=0V
VI=0V
0.5
V
0.5
0
V
0
0.2
0.8
V
0.2
1.8
V
4.0 µA
-4.0 µA
66 160 500 kΩ
RfXIN
RfXCIN
VRAM
Feedback resistance XIN
Feedback resistance XCIN
RAM retention voltage
The output pins are open
and other pins are Vss
Icc
Power supply current
(Vcc=2.7 to 3.0V)
3.0
MΩ
When clock is stopped
25.0
MΩ
2.0
V
Flash memory
version
f(XIN) = 10MHz
Square wave, no division
8
13 mA
Flash memory
version
f(XCIN) = 32kHz
Square wave, in RAM
25
µA
Flash memory
version
f(XCIN) = 32kHz
Square wave, in Flash
420
µA
f(XCIN) = 32kHz
When a WAIT instruction
6.0
is executed.(Note 2)
µA
Oscillation capacity High
Flash memory
f(XCIN) = 32kHz
version
When a WAIT instruction
is executed.(Note 2)
1.8
µA
Oscillation capacity Low
Topr = 25°C
when clock is stopped
0.7 3.0 µA
IDET4
VDET4 detection dissipation current (Note 3)
IDET3
Reset level detection dissipation current (Note 3)
Note 1: Specify a product of -40°C to 85°C to use it.
Note 2: With one timer operated using fC32.
Note 3: IDET is dissipation current when the following bit is set to "1" (detection circuit enabled).
IDET4: VC27 bit of VCR2 register
IDET3: VC26 bit of VCR2 register
0.6
4
µA
0.4
2
µA
Renesas Technology Corp.
179