M16C26 Datasheet, PDF (181/239 Pages) Renesas Technology Corp – 16-BIT CMOS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/20 SERIES

Udenvdeelropment
Preliminary Specifications Rev.
Specifications in this manual are
Electrical Characteristics (Vcc = 5V)
0.9
tentative
and
subject to change.
SINGLE-CHIP 16-BIT
M16C/26 Group
CMOS MICROCOMPUTER
Table 1.18.10. Electrical characteristics (referenced to VCC = 4.2V to 5.5V, VSS = 0V
VCC = 5V
at Topr = – 20^oC to 85^oC / – 40^oC to 85^oC (Note 2), f(XIN) = 20MHZ unless otherwise specified)
Symbol
Parameter
HIGH output P15 to P17, P60 to P67, P72 to P77, P80 to P83,
voltage
P85 to P87, P90 to P93, P100 to P107
VOH
Measuring condition
IOH=-5mA
Standard
Min. Typ. Max.
Unit
3.0
VCC
V
HIGH output P15 to P17, P60 to P67, P72 to P77, P80 to P83,
VOH
voltage
P85 to P87, P90 to P93, P100 to P107
IOH=-200µA
4.7
VCC
V
HIGH output _XOUT
VOH
voltage
HIGH output XCOUT
voltage
HIGHPOWER
LOWPOWER
HIGHPOWER
LOWPOWER
LOW output ^{P15 to P17, P60 to P67, P70 to P77, P80 to P83,}
voltage
P85 to P87, P90 to P93, P100 to P107
VOL
IOL=-1mA
IOH=-0.5mA
With no load applied
With no load applied
IOL=5mA
3.0
VCC
V
3.0
VCC
2.5
V
1.6
2.0
V
LOW output P15 to P17, P60 to P67, P70 to P77, P80 to P83,
voltage
P85 to P87, P90 to P93, P100 to P107
VOL
IOL=200µA
0.45
V
VOL
VT+-VT-
VT+-VT-
IIH
LOW output _XOUT
voltage
HIGHPOWER
LOWPOWER
LOW output _XCOUT
voltage
HIGHPOWER
LOWPOWER
Hysteresis
TA0IN to TA4IN, TB0IN to TB2IN,
INT0, INT1, INT3 to INT5, NMI,
ADTRG, CTS0 to CTS2, SCL, SDA,
CLK0 to CLK2, TA2OUT to TA4OUT,
KI0 to KI3, RxD0 to RxD2
Hysteresis
HIGH input
current
RESET
P15 to P17, P60 to P67, P70 to P77, P80 to P83,
P85 to P87, P90 to P93, P100 to P107
XIN, RESET, CNVss
IOL=1mA
IOL=0.5mA
With no load applied
With no load applied
VI=5V
2.0
V
2.0
0
V
0
0.2
1.0
V
0.2
2.5
V
5.0 µA
LOW input ^{P15 to P17, P60 to P67, P70 to P77, P80 to P83,}
current
P85 to P87, P90 to P93, P100 to P107
IIL
XIN, RESET, CNVss
VI=0V
-5.0 µA
RPULLUP _Pull-up
P15 to P17, P60 to P67, P72 to P77, P80 to P83,
resistance P85 to P87, P90 to P93, P100 to P107
VI=0V
RfXIN
RfXCIN
VRAM
Feedback resistance
Feedback resistance
RAM retention voltage
XIN
XCIN
The output pins are open and
other pins are Vss
Icc
Power supply current
(Vcc = 3.0 to 5.5V)
When clock is stopped
Flash memory
version
Flash memory
version
Flash memory
version
Flash memory
version
f(XIN) = 20MHz
Square wave, no division
f(XCIN) = 32kHz
Square wave, in RAM
f(XCIN) = 32kHz
Square wave, in Flash
f(XCIN) = 32kHz
When a WAIT instruction
is executed. (Note 1)
Oscillation capacity High
f(XCIN) = 32kHz
When a WAIT instruction
is executed. (Note 1)
Oscillation capacity Low
Topr = 25°C
when clock is stopped
IDET4 VDET4 detection dissipation current (Note 3)
IDET3 Reset level detection dissipation current (Note 3)
Note 1: With one timer operated using fC32.
Note 2: Specify a product of -40°C to 85°C to use it.
Note 3: IDET is dissipation current when the following bit is set to "1" (detection circuit enabled)
30.0 50.0 170.0 kΩ
1.5
15
2.0
16
MΩ
MΩ
V
19 mA
25
µA
420
µA
7.5
µA
2.0
µA
0.8 3.0 µA
0.7
4
µA
1.2
8
µA
Renesas Technology Corp.
175