PIC16F707 Datasheet, PDF (80/284 Pages) Microchip Technology – 40/44-Pin, Flash Microcontrollers with nanoWatt XLP and mTouch™ Technology

PIC16F707/PIC16LF707
9.1 ADC Configuration
When configuring and using the ADC the following
functions must be considered:
• Port configuration
• Channel selection
• ADC voltage reference selection
• ADC conversion clock source
• Interrupt control
• Results formatting
9.1.1 PORT CONFIGURATION
The ADC can be used to convert both analog and
digital signals. When converting analog signals, the I/O
pin should be configured for analog by setting the
associated TRIS and ANSEL bits. Refer to Section 6.0
“I/O Ports” for more information.
Note:
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
9.1.2 CHANNEL SELECTION
The CHS bits of the ADCON0 register determine which
channel is connected to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 9.2
“ADC Operation” for more information.
9.1.3 ADC VOLTAGE REFERENCE
The ADREF bits of the ADCON1 register provides
control of the positive voltage reference. The positive
voltage reference can be either VDD, an external
voltage source or the internal Fixed Voltage Reference.
The negative voltage reference is always connected to
the ground reference. See Section 10.0 “Fixed
Voltage Reference” for more details on the Fixed
Voltage Reference.
9.1.4
CONVERSION CLOCK
The source of the conversion clock is software select-
able via the ADCS bits of the ADCON1 register. There
are seven possible clock options:
• FOSC/2
• FOSC/4
• FOSC/8
• FOSC/16
• FOSC/32
• FOSC/64
• FRC (dedicated internal oscillator)
The time to complete one bit conversion is defined as
TAD. One full 8-bit conversion requires 10 TAD periods
as shown in Figure 9-2.
For correct conversion, the appropriate TAD
specification must be met. Refer to the A/D conversion
requirements in Section 25.0 “Electrical
Specifications” for more information. Table 9-1 gives
examples of appropriate ADC clock selections.
Note:
Unless using the FRC, any changes in the
system clock frequency will change the
ADC clock frequency, which may
adversely affect the ADC result.
TABLE 9-1: ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES
ADC Clock Period (TAD)
Device Frequency (FOSC)
ADC
Clock Source
ADCS<2:0>
20 MHz
16 MHz
8 MHz
4 MHz
1 MHz
Fosc/2
Fosc/4
Fosc/8
Fosc/16
Fosc/32
Fosc/64
FRC
000
100 ns⁽²⁾
125 ns⁽²⁾
250 ns⁽²⁾
500 ns⁽²⁾
2.0 s
100
200 ns⁽²⁾
250 ns⁽²⁾
500 ns⁽²⁾
1.0 s
4.0 s
001
400 ns⁽²⁾
0.5 s⁽²⁾
1.0 s
2.0 s
8.0 s⁽³⁾
101
800 ns
1.0 s
2.0 s
4.0 s
16.0 s⁽³⁾
010
1.6 s
2.0 s
4.0 s
8.0 s⁽³⁾
32.0 s⁽³⁾
110
3.2 s
4.0 s
8.0 s⁽³⁾
16.0 s⁽³⁾
64.0 s⁽³⁾
x11
1.0-6.0 s^(1,4) 1.0-6.0 s^(1,4) 1.0-6.0 s^(1,4) 1.0-6.0 s^(1,4) 1.0-6.0 s^(1,4)
Legend:
Note 1:
2:
3:
4:
Shaded cells are outside of recommended range.
The FRC source has a typical TAD time of 1.6 s for VDD.
These values violate the minimum required TAD time.
For faster conversion times, the selection of another clock source is recommended.
When the device frequency is greater than 1 MHz, the FRC clock source is only recommended if the
conversion will be performed during Sleep.
DS41418A-page 80
Preliminary
 2010 Microchip Technology Inc.