PIC16F707 Datasheet, PDF (26/284 Pages) Microchip Technology – 40/44-Pin, Flash Microcontrollers with nanoWatt XLP and mTouch™ Technology

PIC16F707/PIC16LF707
2.3 PCL and PCLATH
The Program Counter (PC) is 13 bits wide. The low
byte comes from the PCL register, which is a readable
and writable register. The high byte (PC<12:8>) is not
directly readable or writable and comes from
PCLATH. On any Reset, the PC is cleared. Figure 2-2
shows the two situations for the loading of the PC. The
upper example in Figure 2-2 shows how the PC is
loaded on a write to PCL (PCLATH<4:0>  PCH).
The lower example in Figure 2-2 shows how the PC is
loaded during a CALL or GOTO instruction
(PCLATH<4:3>  PCH).
FIGURE 2-2:
LOADING OF PC IN
DIFFERENT SITUATIONS
12
PC
PCH
PCL
87
PCLATH<4:0>
5
0
8
Instruction with
PCL as
Destination
ALU Result
PCLATH
PCH
12 11 10
PC
87
2 ^PCLATH<4:3>
PCL
0
GOTO, CALL
11
OPCODE<10:0>
PCLATH
2.3.1 COMPUTED GOTO
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). When
performing a table read using a computed GOTO
method, care should be exercised if the table location
crosses a PCL memory boundary (each 256-byte
block). Refer to Application Note AN556,
“Implementing a Table Read” (DS00556).
2.3.2 STACK
All devices have an 8-level x 13-bit wide hardware
stack (refer to Figure 2-1). The stack space is not part
of either program or data space and the Stack Pointer
is not readable or writable. The PC is PUSHed onto the
stack when a CALL instruction is executed or an
interrupt causes a branch. The stack is POPed in the
event of a RETURN, RETLW or a RETFIE instruction
execution. PCLATH is not affected by a PUSH or POP
operation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
PUSH overwrites the value that was stored from the
first PUSH. The tenth PUSH overwrites the second
PUSH (and so on).
Note 1: There are no Status bits to indicate stack
overflow or stack underflow conditions.
2: There are no instructions/mnemonics
called PUSH or POP. These are actions
that occur from the execution of the CALL,
RETURN, RETLW and RETFIE instruc-
tions or the vectoring to an interrupt
address.
2.4 Program Memory Paging
All devices are capable of addressing a continuous 8K
word block of program memory. The CALL and GOTO
instructions provide only 11 bits of address to allow
branching within any 2K program memory page. When
doing a CALL or GOTO instruction, the upper 2 bits of
the address are provided by PCLATH<4:3>. When
doing a CALL or GOTO instruction, the user must ensure
that the page select bits are programmed so that the
desired program memory page is addressed. If a return
from a CALL instruction (or interrupt) is executed, the
entire 13-bit PC is POPed off the stack. Therefore,
manipulation of the PCLATH<4:3> bits is not required
for the RETURN instructions (which POPs the address
from the stack).
Note:
The contents of the PCLATH register are
unchanged after a RETURN or RETFIE
instruction is executed. The user must
rewrite the contents of the PCLATH regis-
ter for any subsequent subroutine calls or
GOTO instructions.
Example 2-1 shows the calling of a subroutine in
page 1 of the program memory. This example assumes
that PCLATH is saved and restored by the Interrupt
Service Routine (if interrupts are used).
EXAMPLE 2-1:
CALL OF A SUBROUTINE
IN PAGE 1 FROM PAGE 0
ORG 500h
PAGESEL SUB_P1 ;Select page 1
;(800h-FFFh)
CALL SUB1_P1 ;Call subroutine in
:
;page 1 (800h-FFFh)
:
ORG
900h ;page 1 (800h-FFFh)
SUB1_P1
:
;called subroutine
;page 1 (800h-FFFh)
:
RETURN
;return to
;Call subroutine
;in page 0
;(000h-7FFh)
DS41418A-page 26
Preliminary
 2010 Microchip Technology Inc.