PIC16F707 Datasheet, PDF (209/284 Pages) Microchip Technology – 40/44-Pin, Flash Microcontrollers with nanoWatt XLP and mTouch™ Technology

PIC16F707/PIC16LF707
25.4
DC Characteristics: PIC16F707/PIC16LF707-I/E
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Sym.
Characteristic
Min.
Typ†
Max. Units
Conditions
VIL
Input Low Voltage
I/O PORT:
D030
with TTL buffer
—
—
0.8
V 4.5V  VDD  5.5V
D030A
—
—
0.15 VDD V 1.8V  VDD  4.5V
D031
D032
with Schmitt Trigger buffer
—
with I²C™ levels
—
MCLR, OSC1 (RC mode)⁽¹⁾
—
—
0.2 VDD V 2.0V  VDD  5.5V
—
0.3 VDD V
—
0.2 VDD V
D033A
OSC1 (HS mode)
—
—
0.3 VDD V
VIH
Input High Voltage
I/O ports:
—
—
D040
with TTL buffer
2.0
—
—
V 4.5V  VDD 5.5V
D040A
0.25 VDD +
—
0.8
—
V 1.8V  VDD  4.5V
D041
with Schmitt Trigger buffer 0.8 VDD
—
with I²C™ levels
0.7 VDD
—
—
V 2.0V  VDD  5.5V
—
V
D042
MCLR
0.8 VDD
—
—
V
D043A
OSC1 (HS mode)
0.7 VDD
—
—
V
D043B
IIL
OSC1 (RC mode)
Input Leakage Current⁽²⁾
0.9 VDD
—
—
V (Note 1)
D060
D061
I/O ports
MCLR⁽³⁾
—
±5
± 125 nA VSS  VPIN  VDD, Pin at high-
impedance, 85°C
±5
± 1000 nA 125°C
—
± 50
± 200
nA VSS  VPIN  VDD, 85°C
IPUR PORTB Weak Pull-up Current
D070*
VOL
Output Low Voltage⁽⁴⁾
25
100
200
VDD = 3.3V, VPIN = VSS
25
140
300
A VDD = 5.0V, VPIN = VSS
D080
I/O ports
VOH
Output High Voltage⁽⁴⁾
IOL = 8mA, VDD = 5V
—
—
0.6
V IOL = 6mA, VDD = 3.3V
IOL = 1.8mA, VDD = 1.8V
D090
I/O ports
VDD - 0.7
—
IOH = 3.5mA, VDD = 5V
—
V IOH = 3mA, VDD = 3.3V
IOH = 1mA, VDD = 1.8V
Capacitive Loading Specs on Output Pins
D101* COSC2 OSC2 pin
—
—
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1
D101A* CIO
All I/O pins
—
—
50
pF
Program Flash Memory
Legend: TBD = To Be Determined
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: Including OSC2 in CLKOUT mode.
 2010 Microchip Technology Inc.
Preliminary
DS41418A-page 209