K5L5628JTM Datasheet, PDF (46/98 Pages) Samsung semiconductor – 256M Bit (16M x16) Synchronous Burst , Multi Bank NOR Flash / 128M Bit(8M x16) Synchronous Burst UtRAM

K5L5628JT(B)M
PPrreelliimmiinnaarryy
MCP MEMORY
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Vcc
Vcc
-0.5 to +2.5
Voltage on any pin relative to VSS VPP
-0.5 to +9.5
V
VIN
All Other Pins
-0.5 to +2.5
Temperature Under Bias
Tbias
-30 to +125
°C
Storage Temperature
Tstg
-65 to +150
°C
Short Circuit Output Current
IOS
5
mA
Operating Temperature
TA
-30 to + 85
°C
Notes :
1. Minimum DC voltage is -0.5V on Input/ Output pins. During transitions, this level may fall to -1.5V for periods <20ns.
Maximum DC voltage is Vcc+0.6V on input / output pins which, during transitions, may overshoot to Vcc+1.5V for periods <20ns.
2. Minimum DC input voltage is -0.5V on VPP . During transitions, this level may fall to -1.5V for periods <20ns.
Maximum DC input voltage is +9.5V on VPP which, during transitions, may overshoot to +11.0V for periods <20ns.
3. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to the conditions
detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
RECOMMENDED OPERATING CONDITIONS ( Voltage reference to GND )
Parameter
Symbol
Min
Typ.
Max
Supply Voltage
VCC
1.7
1.8
1.95
Supply Voltage
VSS
0
0
0
DC CHARACTERISTICS
Parameter
Symbol
Test Conditions
Min
Typ
Input Leakage Current
ILI
VIN=VSS to VCC, VCC=VCCmax
- 1.0
-
VPP Leakage Current
ILIP VCC=VCCmax , VPP=9.5V
-
-
Output Leakage Current
ILO VOUT=VSS to VCC, VCC=VCCmax, OE=VIH
- 1.0
-
Active Burst Read Current
ICCB1 CE=VIL, OE=VIH
-
30
Active Asynchronous
Read Current
ICC1 CE=VIL, OE=VIH
10MHz
-
30
1MHz
-
3
Active Write Current (Note 2)
ICC2 CE=VIL, OE=VIH, WE=VIL, VPP=VIH
-
15
Read While Write Current
ICC3 CE=VIL, OE=VIH
-
40
Accelerated Program Current
ICC4 CE=VIL, OE=VIH , VPP=9.5V
-
15
Standby Current
ICC5 CE= RESET=VCC ± 0.2V
-
25
Standby Current During Reset
ICC6 RESET = VSS ± 0.2V
-
25
Automatic Sleep Mode(Note 3)
ICC7
CE=VSS ± 0.2V, Other Pins=VIL or VIH
VIL = VSS ± 0.2V, VIH = VCC ± 0.2V
-
25
Input Low Voltage
VIL
-0.5
-
Input High Voltage
Output Low Voltage
Output High Voltage
VIH
VOL
VOH
IOL = 100 µA , VCC=VCCmin
IOH = -100 µA , VCC=VCCmin
VCC-0.4
-
-
-
VCC-0.1
-
Voltage for Accelerated Program VID
8.5
9.0
Low VCC Lock-out Voltage
VLKO
1.0
-
Unit
V
V
Max
Unit
+ 1.0
µA
35
µA
+ 1.0
µA
45
mA
45
mA
5
mA
30
mA
70
mA
30
mA
70
µA
70
µA
70
µA
0.4
V
VCC+0.4
V
0.1
V
-
V
9.5
V
1.3
V
Notes:
1. Maximum ICC specifications are tested with VCC = VCCmax.
2. ICC active while Internal Erase or Internal Program is in progress.
3. Device enters automatic sleep mode when addresses are stable for tAA + 60ns.
46
Revision 1.0
November 2004