PIC18F1220_07 Datasheet, PDF (244/308 Pages) Microchip Technology – 18/20/28-Pin High-Performance, Enhanced Flash Microcontrollers with 10-bit A/D and nanoWatt Technology

PIC18F1220/1320
22.2 DC Characteristics: Power-Down and Supply Current
PIC18F1220/1320 (Industrial)
PIC18LF1220/1320 (Industrial) (Continued)
PIC18LF1220/1320
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F1220/1320
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)^(2,3)
PIC18LF1220/1320 140 220 μA
-40°C
145 220 μA
+25°C
VDD = 2.0V
155 220 μA
+85°C
PIC18LF1220/1320 215 330 μA
225 330 μA
235 330 μA
All devices 385 550 μA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 1 MHz
(RC_RUN mode,
Internal oscillator source)
390 550 μA
405 550 μA
+25°C
+85°C
VDD = 5.0V
Extended devices 410 650 μA
+125°C
PIC18LF1220/1320 410 600 μA
-40°C
425 600 μA
+25°C
VDD = 2.0V
435 600 μA
+85°C
PIC18LF1220/1320 650 900 μA
670 900 μA
680 900 μA
All devices 1.2 1.8 mA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
Internal oscillator source)
1.2 1.8 mA
1.2 1.8 mA
+25°C
+85°C
VDD = 5.0V
Extended devices 1.2 1.8 mA
+125°C
Legend:
Note 1:
2:
3:
4:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
DS39605F-page 242
© 2007 Microchip Technology Inc.