PIC18F1220_07 Datasheet, PDF (154/308 Pages) Microchip Technology – 18/20/28-Pin High-Performance, Enhanced Flash Microcontrollers with 10-bit A/D and nanoWatt Technology

PIC18F1220/1320
16.5 EUSART Synchronous
Slave Mode
Synchronous Slave mode is entered by clearing bit,
CSRC (TXSTA<7>). This mode differs from the
Synchronous Master mode in that the shift clock is
supplied externally at the RB1/AN5/TX/CK/INT1 pin
(instead of being supplied internally in Master mode).
This allows the device to transfer or receive data while
in any low-power mode.
16.5.1 EUSART SYNCHRONOUS
SLAVE TRANSMIT
The operation of the Synchronous Master and Slave
modes are identical, except in the case of the Sleep
mode.
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
a) The first word will immediately transfer to the
TSR register and transmit.
b) The second word will remain in the TXREG
register.
c) Flag bit, TXIF, will not be set.
d) When the first word has been shifted out of TSR,
the TXREG register will transfer the second
word to the TSR and flag bit, TXIF, will now be
set.
e) If enable bit, TXIE, is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
To set up a Synchronous Slave Transmission:
1. Enable the synchronous slave serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
2. Clear bits CREN and SREN.
3. If interrupts are desired, set enable bit TXIE.
4. If 9-bit transmission is desired, set bit TX9.
5. Enable the transmission by setting enable bit
TXEN.
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
7. Start transmission by loading data to the TXREG
register.
8. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TABLE 16-9: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Name
Bit 7
Bit 6
Bit 5 Bit 4 Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Value on
all other
Resets
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u
PIR1
—
ADIF
RCIF TXIF
— CCP1IF TMR2IF TMR1IF -000 -000 -000 -000
PIE1
—
ADIE
RCIE TXIE
— CCP1IE TMR2IE TMR1IE -000 -000 -000 -000
IPR1
—
ADIP
RCIP TXIP
— CCP1IP TMR2IP TMR1IP -111 -111 -111 -111
RCSTA
SPEN
RX9
SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x
TXREG EUSART Transmit Register
0000 0000 0000 0000
TXSTA
CSRC
TX9
TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010
BAUDCTL
—
RCIDL
—
SCKP BRG16
—
WUE ABDEN -1-1 0-00 -1-1 0-00
SPBRGH Baud Rate Generator Register High Byte
0000 0000 0000 0000
SPBRG Baud Rate Generator Register Low Byte
0000 0000 0000 0000
Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
DS39605F-page 152
© 2007 Microchip Technology Inc.