M16C6N4 Datasheet, PDF (345/406 Pages) Renesas Technology Corp – 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY / M16C/60 SERIES

Under development
This document is under development and its contents are subject to change.
M16C/6N Group (M16C/6N4)
22. Electric Characteristics (Normal-ver.)
Table 22.51 Electrical Characteristics ⁽¹⁾
Symbol
Parameter
VCC = 3.3V
Measuring Condition
Standard
Min. Typ. Max.
Unit
VOH HIGH Output P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, IOH = –1mA
Voltage
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
VCC-0.5
VCC
V
P6_0 to P6_7, P7_0, P7_2 to P7_7,
P8_0 to P8_4, P8_6, P8_7, P9_0,
P9_2 to P9_7, P10_0 to P10_7
VOH HIGH Output XOUT HIGHPOWER
Voltage
LOWPOWER
HIGH Output
Voltage
XCOUT HIGHPOWER
LOWPOWER
IOH = –0.1mA
VCC-0.5
VCC
V
IOH = –50µA
VCC-0.5
VCC
With no load applied
2.5
V
With no load applied
1.6
VOL
LOW Output P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, IOL = 1mA
Voltage
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
0.5 V
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_4,
P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7
VOL
LOW Output XOUT HIGHPOWER
IOL = 0.1mA
0.5 V
Voltage
LOWPOWER
IOL = 50µA
0.5
LOW Output XCOUT HIGHPOWER
With no load applied
0
V
Voltage
VT+-VT- Hysteresis
LOWPOWER
With no load applied
0
_________ _______
HOLD, RDY, TA0IN to TA4IN, TB0IN to TB5IN,
0.2
0.8 V
________ ________ _______ _____________ _________ _________
INT0 to INT5, NMI, ADTRG, CTS0 to CTS2,
SCL0 to SCL2, SDA0 to SDA2, CLK0 to CLK3,
_____
_____
TA0OUT to TA4OUT, KI0 to KI3,
VT+-VT- Hysteresis
RXD0 to RXD2, SIN3
_____________
RESET
0.2
1.8 V
VT+-VT- Hysteresis
IIH
HIGH Input
Current
XIN
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, VI = 3.3V
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
0.2
0.8 V
4.0 µA
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7,
____________
XIN, RESET, CNVSS, BYTE
IIL
LOW Input
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, VI = 0V
Current
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
–4.0 µA
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7,
____________
XIN, RESET, CNVSS, BYTE
RPULLUP Pull-up
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, VI = 0V
50 100 500 kΩ
Resistance
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
P6_0 to P6_7, P7_0, P7_2 to P7_7, P8_0 to
P8_4, P8_6, P8_7, P9_0, P9_2 to P9_7,
P10_0 to P10_7
RfXIN Feedback Resistance XIN
3.0
MΩ
RfXCIN Feedback Resistance XCIN
25
MΩ
VRAM RAM Retention Voltage
At stop mode
2.0
V
NOTES:
1. Referenced to VCC = 3.0 to 3.6V, VSS = 0V at Topr = –40 to 85°C, f(BCLK) = 24MHz unless otherwise specified.
Rev.2.30 Oct 24, 2005 page 327 of 376
REJ09B0009-0230