|
XRT7250 Datasheet, PDF (28/463 Pages) Exar Corporation – DS3/E3 FRAMER IC | |||
|
◁ |
áç
PIN DESCRIPTION
PIN #
56
NAME
TxOHEnable
57
TxOHFrame
58
TxNibFrame
59
TxNibClk
60
GND
61
TxFrame
62
VDD
DS3/E3 FRAMER IC
XRT7250
REV. 1.1.1
TYPE
DESCRIPTION
O Transmit Overhead Input Enable.
The XRT7250 will assert this signal, for one âTxInClkâ period, just prior to the
instant that the âTransmit Overhead Data Input Interfaceâ will be sampling and
processing an overhead bit.
If the Terminal Equipment intends to insert its own value for an overhead bit,
into the outbound DS3 or E3 frame, it is expected to sample the state of this
signal, upon the falling edge of âTxInClkâ. Upon sampling the âTxOHEnableâ
high, the Terminal Equipment should (1) place the desired value of the over-
head bit, onto the âTxOHâ input pin and (2) assert the âTxOHInsâ input pin. The
Transmit Overhead Data Input Interfaceâ block will sample and latch the data
on the âTxOHâ signal, upon the rising edge of the very next âTxInClkâ input sig-
nal.
O Transmit Overhead Framing Pulse:
This output pin pulses "high" when the Transmit Overhead Data Input Interface
block is expecting the first Overhead bit, within a DS3 or E3 frame to be applied
to the TxOH input pin.
This pin is "high" for one clock period of TxOHClk.
O Transmit Frame Boundary Indicator - Nibble/Parallel Interface
This output pin pulses "high" when the last nibble of a given DS3 or E3 frame is
expected at the TxNib[3:0] input pins.
The purpose of this output pin is to alert the Terminal Equipment that it needs
to begin transmission of a new DS3 or E3 frame to the XRT7250.
O Transmit Nibble Clock Signal
If the user opts to operate the XRT7250 in the âNibble-Parallelâ mode,
then the XRT7250 will derive this clock signal from either the âTxInClkâ
or the âRxLineClkâ signal (depending upon which signal is selected as
the timing reference).
The user is advised to configure the Terminal Equipment to output the
âoutboundâ payload data (to the XRT7250 Framer IC) onto the âTx-
Nib[3:0]â input pins, upon the rising edge of this clock signal.
NOTES:
1. For DS3 applications, the XRT7250 Framer IC will output 1176 clock
edges (to the Terminal Equipment) for each âoutboundâ DS3 frame.
2. For E3, ITU-T G.832 applications, the XRT7250 Framer IC will output
1074 clock edges (to the Terminal Equipment) for each âoutboundâ E3
frame.
3. For E3, ITU-T G.751 applications, the XRT7250 Framer IC will output
384 clock edges (fo the Terminal Equipment) for each âoutboundâ E3
frame.
**** Ground Pin
O Transmit End of DS3 or E3 Frame Indicator:
The Transmit Section of the XRT7250 will pulse this output pin "high" (for one
bit-period), when the Transmit Payload Data Input Interface is processing the
last bit of a given DS3 or E3 frame.
The purpose of this output pin is to alert the Terminal Equipment that it needs
to begin transmission of a new DS3 or E3 frame to the XRT7250 (e.g., to per-
mit the XRT7250 to maintain Transmit DS3/E3 framing alignment control over
the Terminal Equipment).
**** Power Supply pin
9
|
▷ |