AMD-766 Datasheet, PDF (53/96 Pages) Advanced Micro Devices – Peripheral Bus Controller

23167B – March 2001
Preliminary Information
AMD-766^TM Peripheral Bus Controller Data Sheet
C1A4C: EIDE Controller Cycle Time and Address Setup Time Register
Configuration space; function 1; offset: 4F-4Ch. Default: FFFF 00FFh. Read-write.
For bits[7:0] the value in each 2-bit field, plus one, specifies the address setup time in 30 nanosecond PCI clocks; this
applies to all PIO and multi-word DMA cycles. For bits[31:16] the value in each 4-bit field, plus one, specifies the
time in 30 nanosecond PCI clocks; this applies address ports 171h though 177h, 1F1h though 1F7h, 376h, and 3F6h.
For 170h and 1F0h, see C1A48.
31:28
PXPW
27:24
PXRT
23:20
SXPW
19:16
SXRT
15:8
Reserved
7:6 5:4 3:2 1:0
P0ADD P1ADD S0ADD S1ADD
S1ADD[1:0] Secondary Drive 1 Address Setup Time.
S0ADD[1:0] Secondary Drive 0 Address Setup Time.
P1ADD[1:0] Primary Drive 1 Address Setup Time.
P0ADD[1:0] Primary Drive 0 Address Setup Time.
SXRT[3:0] Secondary Non-170 DIOR#/DIOW# Recovery Time.
SXPW[3:0] Secondary Non-170 DIOR#/DIOW# Active Pulse Width.
PXRT[3:0] Primary Non-1F0 DIOR#/DIOW# Recovery Time.
PXPW[3:0] Primary Non-1F0 DIOR#/DIOW# Active Pulse Width.
C1A50: EIDE Controller UDMA Extended Timing Control Register
Configuration space; function 1; offset: 53-50h. Default: 0303 0303h.
Each byte of this register controls UDMA mode for access to the specified drive. Bits[7:0] specify the secondary
slave drive; bits[15:8] specify the secondary master drive; bits[23:16] specify the primary slave drive; and bits[31:24]
specify the primary master drive.
31:24
23:16
15:8
7:0
P0UDMA
P1UDMA
S0UDMA
S1UDMA
[P0, P1, S0, S1]UDMA[2:0] [Primary, Secondary] Drive [1,0] Cycle Time, [P0, P1, S0, S1]CYCT. Read-write.
Bits[2:0] UDMA mode
Cycle time
0
UDMA mode 2
60 nanoseconds
1
UDMA mode 1
90 nanoseconds
2
UDMA mode 0
120 nanoseconds
3
Slow UDMA mode 0
150 nanoseconds
4
UDMA mode 3
45 nanoseconds
5
UDMA mode 4
30 nanoseconds
6
UDMA mode 5
20 nanoseconds
[P0, P1, S0, S1]UDMA[5:3]. Read only. These bits are fixed at their default values.
[P0, P1, S0, S1]UDMA[6] [Primary, Secondary] Drive [1,0] Ultra DMA Mode Enable,
[P0, P1, S0, S1]UDMAEN. Read-write. 1=Enable UDMA mode.
[P0, P1, S0, S1]UDMA[7] [Primary, Secondary] Drive [1,0] Ultra DMA Mode Enable Method,
[P0, P1, S0, S1]ENMODE. Read-write. 1=Enable UDMA mode by setting bit 6 of this register. 0=Enable UDMA
mode by detecting the “Set Feature” ATA command.
53