DS90UB914A-Q1 Datasheet, PDF (7/61 Pages) Texas Instruments – 25-MHz to 100-MHz 10/12-Bit FPD-Link III Deserializer

www.ti.com
DS90UB914A-Q1
SNLS499A – APRIL 2016 – REVISED JUNE 2016
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)⁽¹⁾
Supply Voltage – V_{DD_n} (1.8 V)
Supply Voltage – V_DDIO
LVCMOS Input Voltage
CML Receiver I/O Voltage (V_DD)
Junction Temperature
Storage temperature range, T_stg
MIN
−0.3
−0.3
−0.3
-0.3
-65
MAX
2.5
4.0
V_DDIO + 0.3
V_DD + 0.3
150
150
UNIT
V
V
V
V
°C
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
V_(ESD)
Electrostatic
discharge
ESD Rating (IEC 61000-4-2)
R_D = 330 Ω, C_s = 150pF
ESD Rating (ISO10605)
R_D = 330 Ω, C_s = 150/330 pF
R_D = 2 KΩ, C_s = 150/330 pF
Human body model (HBM), per AEC Q100-002⁽¹⁾
Charged device model (CDM), per AEC
Q100-011
Corner pins (1, 12, 13, 24,
25, 36, 37, 48)
Other pins
Air Discharge
(DOUT+, DOUT-, RIN+, RIN-)
Contact Discharge
(DOUT+, DOUT-, RIN+, RIN-)
Air Discharge
(DOUT+, DOUT-, RIN+, RIN-)
Contact Discharge
(DOUT+, DOUT-, RIN+, RIN-)
VALUE
±8000
±1000
±25000
±7000
±15000
±8000
(1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
UNIT
V
V
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply Voltage (V_{DD_n})
LVCMOS Supply Voltage (V_DDIO= 1.8V) OR
LVCMOS Supply Voltage (V_DDIO= 3.3V)
Supply Noise⁽¹⁾
V_{DD_n} (1.8 V)
V_DDIO (1.8 V)
V_DDIO (3.3 V)
Operating Free Air Temperature (T_A)
PCLK Clock Frequency
MIN
NOM
MAX
UNIT
1.71
1.8
1.89
V
1.71
1.8
1.89
V
3.0
3.3
3.6
25
25
mVp-p
50
–40
25
105
°C
25
100
MHz
(1) Supply noise testing was done with minimum capacitors (as shown on Pin Configuration and Functions and Figure 33 on the PCB. A
sinusoidal signal is AC coupled to the V_{DD_n} (1.8 V) supply with amplitude = 25 mVp-p measured at the device V_{DD_n} pins. Bit error rate
testing of input to the Ser and output of the Des with 10-meter cable shows no error when the noise frequency on the Ser is less than 1
MHz. The Des on the other hand shows no error when the noise frequency is less than 750 kHz.
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: DS90UB914A-Q1
Submit Documentation Feedback
7