C517A_99 Datasheet, PDF (2/218 Pages) Siemens Semiconductor Group – 8-Bit CMOS Microcontroller

C517A User’s Manual
Revision History :
Previous Releases :
Page
(previous
version)
Page
(new
version)
All sections
1-2
1-2
1-4
1-5
1-5 to 1-10
1-8
6-24
9-1
9-2
9-3
All sections
1-2
1-2
1-4
1-5
1-6 to 1-13
1-9
6-24
9-1
9-1
9-1
9-5
9-3
9-7
9-5
9-7
9-5
9-9
9-7
Chapter 10 -
01.99
08.97 (Original Version)
Subjects (changes since last revision)
9_CC is changed to 9_DD.
"with wake-up capability through INT0 pin" is removed.
P-LCC-84 package is added under the main feature list.
P-LCC-84 package is added.
Figure 1-4; added.
Table 1-1; modified, column “P-LCC-84” is added.
Description for pin EA is added with "For C517A-4R ...”
Table 6-3; modified, column “Pin No. (P-LCC-84)” is added.
The whole page is added to contain brief explanation of the power saving modes.
Section 9.1 and 9.2 are added to give more explanation of pin PE/SWD usage.
Last paragrapah; the sentence “Changing the logic level ...” in the note under the
description of PCON is deleted.
1st paragraph; the sentence “If the idle mode ...” is added.
3rd paragraph; the paragraph is changed to contain an extra way to leave
software power down mode.
4th paragraph; the sentece “If the software power down ...” is added.
Paragraph "A low signal at the P3.2/INT0 ...." is removed.
The whole chapter is moved to the C517A Data Sheet.
Edition 01.99
This edition was realized using the software system FrameMaker^®.
Published by Siemens AG,
Bereich Halbleiter, Marketing-
Kommunikation, Balanstraße 73,
81541 München
© Siemens AG 01.99.
All Rights Reserved.
Attention please!
As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for ap-
plications, processes and circuits implemented within components or assemblies.
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved.
For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or the
Siemens Companies and Representatives worldwide (see address list).
Due to technical requirements components may contain dangerous substances. For information on the types in ques-
tion please contact your nearest Siemens Office, Semiconductor Group.
Siemens AG is an approved CECC manufacturer.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office.
By agreement we will take packing material back, if it is sorted. You must bear the costs of transport.
For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice
you for any costs incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose!
Critical components¹ of the Semiconductor Group of Siemens AG, may only be used in life-support devices or
systems² with the express written approval of the Semiconductor Group of Siemens AG.
1 A critical component is a component used in a life-support device or system whose failure can reasonably be ex-
pected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device
or system.
2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or main-
tain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered.