MC68HC05B4 Datasheet, PDF (215/298 Pages) Motorola, Inc – High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcomputer Unit

Table E-12 Control timing for 3.3V operation
(V_DD = 3.3Vdc ± 10%, V_SS = 0 Vdc, T_A = T_L to T_H)
Characteristic
Symbol
Frequency of operation
Crystal option
External clock option
Internal operating frequency (f_OSC /2)
Using crystal
Using external clock
Cycle time (see Figure 9-1)
Crystal oscillator start-up time (see Figure 9-1)
Stop recovery start-up time (crystal oscillator)
RC oscillator stabilization time
A/D converter stabilization time
External RESET input pulse width
Power-on RESET output pulse width
4064 cycle
16 cycle
Watchdog RESET output pulse width
Watchdog time-out
EEPROM byte erase time
0 to 70 (standard)
– 40 to 85 (extended)
– 40 to 105 (industrial)
– 40 to 125 (automotive)
EEPROM byte program time ⁽¹⁾
0 to 70 (standard)
– 40 to 85 (extended)
– 40 to 105 (industrial)
– 40 to 125 (automotive)
Timer (see Figure E-11)
Resolution⁽²⁾
Input capture pulse width
Input capture pulse period
Interrupt pulse width (edge-triggered)
Interrupt pulse period
OSC1 pulse width ⁽⁵⁾
Write/Erase endurance⁽⁶⁾⁽⁷⁾
Data retention⁽⁶⁾⁽⁷⁾
f_OSC
f_OSC
f_OP
f_OP
t_CYC
O^t XOV
IL^t CH
A^t DRC
t_ADON
t_RL
t_PORL
t_PORL
t_DOGL
t _DOG
t_ERA
t_ERA
t_ERA
t_ERA
t_{PR OG}
t_{PR OG}
t_{PR OG}
t_{PR OG}
t_RESL
t_TH, t_TL
t_TLTL
I^tLIH
t_ILIL
t_OH , t_OL
—
—
Min
Max Unit
—
2.0 MHz
dc
2.0 MHz
—
1.0 MHz
dc
1.0 MHz
1000
—
ns
—
100
ms
100
ms
5
µs
500
µs
1.5
—
t _CYC
4064
16
—
—
t_CYC
t_CYC
1.5
—
t _CYC
6144
7168 t _CYC
30
—
ms
30
—
ms
30
—
ms
30
—
ms
30
—
ms
30
—
ms
30
—
ms
30
—
ms
4
—
250
—
— ⁽³⁾
—
250
—
— ⁽⁴⁾
—
200
—
10000
10
t_CYC
ns
t_CYC
ns
t _CYC
ns
cycles
years
(1) For bus frequencies less than 2 MHz, the internal RC oscillator should be used when
programming the EEPROM.
(2)
Since a 2-bit prescaler in the timer must count
factor in determining the timer resolution.
four
external
cycles
C^(tYC ^{), this}
is
the
limiting
(3) The minimum period t_TLTL should not be less than the number of cycle times it takes to
execute the capture interrupt service routine plus 24 _Ct _YC .
(4) The minimum period t_ILIL should not be less than the number of cycle times it takes to execute
the interrupt service routine plus 21 _Ct _YC .
(5) t_OH and t_OL should not total less than 500ns.
(6) At a temperature of 85°C
(7) Refer to Reliability Monitor Report (current quarterly issue) for current failure rate information.
14
MC68HC05B6
Rev. 4
MC68HC705B16
TPG
MOTOROLA
E-27