XRT72L52 Datasheet, PDF (375/480 Pages) Exar Corporation – TWO CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER

áç
PRELIMINARY
XRT72L52
TWO CHANNEL DS3/E3 FRAMER IC WITH HDLC CONTROLLER
REV. P1.1.3
In this mode, the Transmit Section of the XRT72L52
will use the TxInClk signal as its timing reference.
B. Serial Mode
The XRT72L52 will receive the E3 payload data, in a
serial manner, via the TxSer input pin. The Transmit
Payload Data Input Interface (within the XRT72L52)
will latch this data into its circuitry, on the rising edge
of the TxInClk input clock signal.
C. Delineation of Outbound DS3 frames (Frame
Master Mode)
The Transmit Section of the XRT72L52 will use the
TxInClk signal as its timing reference, and will initiate
E3 frame generation, asynchronously with respect to
any externally applied signal. The XRT72L52 will
pulse its TxFrame output pin "High" whenever its it
processing the very last bit-field within a given E3
frame.
D. Sampling of payload data, from the Terminal
Equipment
In Mode 3, the XRT72L52 will sample the data, at the
TxSer input pin, on the rising edge of TxInClk.
Interfacing the Transmit Payload Data Input Inter-
face block of the XRT72L52 to the Terminal Equip-
ment for Mode 3 Operation
Figure 161 presents an illustration of the Transmit
Payload Data Input Interface block (within the
XRT72L52) being interfaced to the Terminal Equip-
ment, for Mode 3 operation.
FIGURE 161. ILLUSTRATION OF THE TERMINAL EQUIPMENT BEING INTERFACED TO THE TRANSMIT PAYLOAD DATA
INPUT INTERFACE BLOCK OF THE XRT72L52 FOR MODE 3 (SERIAL/LOCAL-TIMED/FRAME-MASTER) OPERATION
34.368 MHz
Clo3c4k.3S6o8uMrcHe ^z
Clock Source
E3_Clock_In
E3_Clock_In
E3_Data_Out
E3_Data_Out
TxStart_of_Frame
TxStart_of_Frame
E3_Overhead_Ind
E3_Overhead_Ind
TxInClk
TxInClk
TxSer
TxSer
TxFrameRef
TxFrameRef
TxOH_Ind
TxOH_Ind
NibInt
NibInt
Terminal Equipment
XRT72L5X E3 Framer
Mode 3 Operation of the Terminal Equipment
In Figure 161, both the Terminal Equipment and the
XRT72L52 are driven by an external 34.368 MHz
clock signal. This clock signal is connected to the
E3_Clock_In input of the Terminal Equipment and the
TxInClk input pin of the XRT72L52.
The Terminal Equipment will serially output the pay-
load data on its E3_Data_Out output pin, upon the
rising edge of the signal at the E3_Clock_In input pin.
Similarly, the XRT72L52 will latch the data, residing
on the TxSer input pin, on the rising edge of TxInClk.
The XRT72L52 will pulse the TxFrame output pin
"High" for one bit-period, coincident while it is pro-
cessing the last bit-field within a given Outbound E3
frame. The Terminal Equipment is expected to moni-
tor the TxFrame signal (from the XRT72L52) and to
place the first bit, within the very next Outbound E3
frame on the TxSer input pin.
NOTE: In this case, the XRT72L52 dictates exactly when
the very next E3 frame will be generated. The Terminal
Equipment is expected to respond appropriately by provid-
ing the XRT72L52 with the first bit of the new E3 frame,
upon demand. Hence, in this mode, the XRT72L52 is
356