XC4VLX100-11FF1148C Datasheet, PDF (56/58 Pages) Xilinx, Inc – DC and Switching Characteristics

Virtex-4 FPGA Data Sheet: DC and Switching Characteristics
Date
12/11/06
(Cont’d)
03/27/07
06/08/07
08/10/07
09/10/07
Version
2.0
(Cont’d)
2.1
2.2
2.3
2.4
Revisions
• Table 50: Removed T_LOCK_FX_MIN parameter. Added DCM_RESET.
• Table 53: Added Note (1), no minimum frequency for PMCD.
• Table 64: Added Note (1) to refer to LX and SX Errata for capability improvements.
• SPEED SPECIFICATION version for this data sheet release: v1.64.
• Table 4: Added Note (6) regarding max quiescent supply current.
• Table 5: Filled in missing power-on current values for FX devices.
• Table 24: Added new parameter F_GREFCLK. Added Min value for Spread Spectrum
Clocking frequency. Corrected “Conditions”.
• Table 26: Revised Notes (2) and (3).
• Table 37, Table 38: Added column/values for XC4VFX -12.
• Table 39: Added columns/values for XC4VFX -11 and -12. Corrected XC4VLX/SX -11
and -12 values for T_REGXB, T_REGYB, and T_CKSH.
• Table 43: Restored parameter T_CONFIG and footnote (1) from earlier revision. Added
new parameter T_SMCO (SelectMAP Readback Clock-to-Out).
• Table 50: Restored DCM_RESET Minimum and DCM_INPUT_CLOCK_STOP
parameters from earlier revision. Added Notes (4) through (7) to these parameters.
• Table 60: Removed FF1760 package. Not supported.
• Table 63: Added FX devices and JTAG IDs.
• SPEED SPECIFICATION version for this data sheet release: v1.65.
• Table 14: Promoted -12 speed grade devices of XC4VFX12, XC4VFX20, and
XC4VFX60 to Production status.
• Table 37: Removed parameter T_{ISCCK_REV}. Not meaningful because pin should always
be connected to GND.
• Table 43: Added parameter F_{MAX_SELECTMAP}. for maximum Slave SelectMAP mode
external configuration clock frequency.
• Table 63: Filled in Step 1 values for XC4VFX20, XC4VFX60, and XC4VFX100.
• Table 65: Added Step 1 data.
• SPEED SPECIFICATION version for this data sheet release: v1.65.
• Table 3: Added MAX value for I_BATT .
• Table 25: Added unit (ns) to RXSIGDET.
• Table 27: Added Note (3) specifying range of DCI reference resistors and referring to
UG070.
• Added section Ethernet MAC Switching Characteristics, page 22, and replaced
Table 29.
• Added section I/O Standard Adjustment Measurement Methodology, page 23,
including Table 30, Table 31, and Figure 4.
• Table 43: Added parameter F_{MAX_ICAP}. Added word “Data” to description of
SelectMAP Setup/Hold.
• Table 64: Added to Capability Improvements, for Step 1 that the DFS macro is no
longer needed.
• SPEED SPECIFICATION version for this data sheet release: v1.67.
• Table 14: Promoted all speed grades for XC4VFX40 devices, and -12 speed grade for
XC4VFX100 devices, to Production status.
• Table 63: Filled in Step 1 value for XC4VFX40.
• Table 65: Added Note 1.
DS302 (v3.7) September 9, 2009
www.xilinx.com
Product Specification
56