CP3BT10 Datasheet, PDF (141/210 Pages) National Semiconductor (TI) – Reprogrammable Connectivity Processor with Bluetooth and USB Interfaces

22.4.1 Timer and Watchdog Configuration Register
(TWCFG)
22.4.2 Timer and Watchdog Clock Prescaler Register
(TWCP)
The TWCFG register is a byte-wide, read/write register that
selects the Watchdog clock input and service method, and
also allows the Watchdog registers to be selectively locked.
A locked register cannot be read or written; a read operation
returns unpredictable values and a write operation is ig-
nored. Once a lock bit is set, that bit cannot be cleared until
the device is reset. At reset, the non-reserved bits of the
register are cleared. The register format is shown below.
The TWCP register is a byte-wide, read/write register that
specifies the prescaler value used for dividing the low-fre-
quency clock to generate the T0IN clock. At reset, the non-
reserved bits of the register are cleared. The register format
is shown below.
7
3
2
0
Reserved
MDIV
76 5
4
3
2
1
0
Res. WDSDME WDCT0I LWDCNT LTWMT0 LTWCP LTWCFG
LTWCFG
LTWCP
LTWMT0
LWDCNT
WDCT0I
WDSDME
The Lock TWCFG Register bit controls ac-
cess to the TWCFG register. When clear, ac-
cess to the TWCFG register is allowed. When
set, the TWCFG register is locked.
0 – TWCFG register unlocked.
1 – TWCFG register locked.
The Lock TWCP Register bit controls access
to the TWCP register. When clear, access to
the TWCP register is allowed. When set, the
TWCP register is locked.
0 – TWCP register unlocked.
1 – TWCP register locked.
The Lock TWMT0 Register bit controls access
to the TWMT0 register. When clear, access to
the TWMT0 and T0CSR registers are al-
lowed. When set, the TWMT0 and T0CSR
registers are locked.
0 – TWMT0 register unlocked.
1 – TWMT0 register locked.
The Lock LDWCNT Register bit controls ac-
cess to the LDWCNT register. When clear, ac-
cess to the LDWCNT register is allowed.
When set, the LDWCNT register is locked.
0 – LDWCNT register unlocked.
1 – LDWCNT register locked.
The Watchdog Clock from T0IN bit selects the
clock source for the Watchdog timer. When
clear, the T0OUT signal (the output of Timer
T0) is used as the Watchdog clock. When set,
the T0IN signal (the prescaled Slow Clock) is
used as the Watchdog clock.
0 – Watchdog timer is clocked by T0OUT.
1 – Watchdog timer is clocked by T0IN.
The Watchdog Service Data Match Enable bit
controls which method is used to service the
Watchdog timer. When clear, Watchdog ser-
vicing is accomplished by writing a count val-
ue to the WDCNT register; write operations to
the Watchdog Service Data Match (WDSDM)
register are ignored. When set, Watchdog
servicing is accomplished by writing the value
5Ch to the WDSDM register.
0 – Write a count value to the WDCNT regis-
ter to service the Watchdog timer.
1 – Write 5Ch to the WDSDM register to ser-
vice the Watchdog timer.
MDIV
Main Clock Divide. This 3-bit field defines the
prescaler factor used for dividing the low
speed device clock to create the T0IN clock.
The allowed 3-bit values and the correspond-
ing clock divisors and clock rates are listed be-
low.
MDIV
Clock Divisor
(f_SCLK = 32.768 kHz)
T0IN
Frequency
000
1
32.768 kHz
001
2
16.384 kHz
010
4
8.192 kHz
011
8
4.096 kHz
100
16
2.056 kHz
101
32
1.024 kHz
Other
Reserved
N/A
22.4.3 TWM Timer 0 Register (TWMT0)
The TWMT0 register is a word-wide, read/write register that
defines the T0OUT interrupt rate. At reset, TWMT0 register
is initialized to FFFFh. The register format is shown below.
15
0
PRESET
PRESET
The Timer T0 Preset field holds the value
used to reload Timer T0 on each underflow.
Therefore, the frequency of the Timer T0 in-
terrupt is the frequency of T0IN divided by
(PRESET+1). The allowed values of PRESET
are 0001h through FFFFh.
141
www.national.com